- 21 Jul, 2020 33 commits
-
-
Mark Starovoytov authored
This patch replaces addition assignment operator with a simple assignment in aq_vec_get_stats() and aq_vec_get_sw_stats(), because it is sufficient in both cases and this change simplifies the introduction of u64_stats_update_* in these functions. Signed-off-by:
Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by:
Igor Russkikh <irusskikh@marvell.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Mark Starovoytov authored
This patch moves FRAC_PER_NS to aq_hw.h so that it can be used in both hw_atl (A1) and hw_atl2 (A2) in the future. Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== Extend testptp with PTP perout waveform Demonstrate the usage of the newly introduced flags in the PTP_PEROUT_REQUEST2 ioctl: https://www.spinics.net/lists/netdev/msg669346.html ==================== Signed-off-by:
-
Vladimir Oltean authored
Extend the example program for PTP ancillary functionality with the ability to configure not only the periodic output's period (frequency), but also the phase and duty cycle (pulse width) which were newly introduced. The ioctl level also needs to be updated to the new PTP_PEROUT_REQUEST2, since the original PTP_PEROUT_REQUEST doesn't support this functionality. For an in-tree testing program, not having explicit backwards compatibility is fine, as it should always be tested with the current kernel headers and sources. Tested with an oscilloscope on the felix switch PHC: echo '2 0' > /sys/class/ptp/ptp1/pins/switch_1588_dat0 ./testptp -d /dev/ptp1 -p 1000000000 -w 100000000 -H 1000 -i 0 Signed-off-by:
Vladimir Oltean <olteanv@gmail.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Vladimir Oltean authored
Since 'perout' holds the nanosecond value of the signal's period, it should be a 64-bit value. Current assumption is that it cannot be larger than 1 second. Signed-off-by:
-
Vaibhav Gupta authored
Drivers using legacy PM have to manage PCI states and device's PM states themselves. They also need to take care of configuration registers. With improved and powerful support of generic PM, PCI Core takes care of above mentioned, device-independent, jobs. This driver makes use of PCI helper functions like pci_save/restore_state(), pci_enable/disable_device(), pci_set_power_state() and pci_set_master() to do required operations. In generic mode, they are no longer needed. Change function parameter in both .suspend() and .resume() to "struct device*" type. Use to_pci_dev() and dev_get_drvdata() to get "struct pci_dev*" variable and drv data. Compile-tested only. Signed-off-by:
Vaibhav Gupta <vaibhavgupta40@gmail.com> Signed-off-by:
-
David S. Miller authored
Alexander Lobakin says: ==================== qed, qede: add support for new operating modes This series covers the support for the following: - new port modes; - loopback modes, previously missing; - new speed/link modes; - several FEC modes; - multi-rate transceivers; and also cleans up and optimizes several related parts of code. v3 (from [2]): - dropped custom link mode declaration; qed, qede and qedf switched to Ethtool link modes and definitions (#0001, #0002, per Andrew Lunn's suggestion); - exchange more .text size to .initconst and .ro_after_init in qede (#0003). v2 (from [1]): - added a patch (#0010) that drops discussed dead struct member; - addressed checkpatch complaints on #0014 (former #0013); - rebased on top of latest net-next; - no other changes. [1] https://lore.kernel.org/netdev/20200716115446.994-1-alobakin@marvell.com/ [2] https://lore.kernel.org/netdev/20200719201453.3648-1-alobakin@marvell.com/ ==================== Signed-off-by:
-
Alexander Lobakin authored
Add all necessary code (NVM parsing, MFW and Ethtool reports etc.) to support extended speed and FEC modes. These new modes are supported by the new boards revisions and newer MFW versions. Misc: correct port type for MEDIA_KR. Signed-off-by:
Alexander Lobakin <alobakin@marvell.com> Signed-off-by:
-
Alexander Lobakin authored
Simplify and lighten qed_set_link() by declaring static link modes maps and populating them on module init. This way we save plenty of text size at the low expense of __ro_after_init and __initconst data (the latter will be purged after module init is done). Misc: sanitize exit callback. Signed-off-by:
-
Alexander Lobakin authored
These modes are relevant only for several boards, but may be reported by MFW as well as the others. Signed-off-by:
-
Alexander Lobakin authored
These ports ship on new boards revisions and are supported by newer firmware versions. Signed-off-by:
-
Alexander Lobakin authored
Struct field qed_hw_info::port_mode isn't used anywhere in the code, so can be safely removed to prevent possible dead code addition. Also remove the enumeration QED_PORT_MODE orphaned after this deletion. Signed-off-by:
-
Alexander Lobakin authored
Reformat a few nvm_cfg* structures (and partly qed_dev) prior to adding new fields and definitions. Signed-off-by:
-
Alexander Lobakin authored
Add Ethtool callbacks for querying and setting FEC parameters if it's supported by the underlying qed module and MFW version running on the device. Signed-off-by:
-
Alexander Lobakin authored
Prior to adding new callbacks, format qede ethtool_ops structs to make declarations more fancy and readable. Signed-off-by:
-
Alexander Lobakin authored
Add all necessary routines for reading supported FEC modes from NVM and querying FEC control to the MFW (if the running version supports it). Signed-off-by:
-
Alexander Lobakin authored
Prior to adding new fields and bitfields, reformat the related structures according to the Linux style (spaces to tabs, lowercase hex, indentation etc.). Signed-off-by:
-
Alexander Lobakin authored
Currently qed driver does not take into consideration transceiver's capabilities when generating link partner's speed advertisement. This leads to e.g. incorrect ethtool link info on 10GbaseT modules. Use transceiver info not only for advertisement and support arrays, but also for link partner's abilities to fix it. Misc: fix a couple of comments nearby. Signed-off-by:
-
Alexander Lobakin authored
Set the corresponding advertised and supported link modes according to the detected transceiver type and device capabilities. Signed-off-by:
-
Alexander Lobakin authored
Prior to adding new bitfields, reformat the existing ones from spaces to tabs, and unify all hex values to lowercase. Signed-off-by:
-
Alexander Lobakin authored
Simplify and lighten qede_set_link_ksettings() by declaring static link modes maps and populating them on module init. This way we save plenty of text size at the low expense of __ro_after_init and __initconst data (the latter will be purged after module init is done). Signed-off-by:
-
Alexander Lobakin authored
Currently qed driver already ran out of 32 bits to store link modes, and this doesn't allow to add and support more speeds. Convert custom link mode to generic Ethtool bitmap and definitions (convenient Phylink shorthands are used for elegance and readability). This allowed us to drop all conversions/mappings between the driver and Ethtool. This involves changes in qede and qedf as well, as they used definitions from shared "qed_if.h". Suggested-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Alexander Lobakin authored
Add a new helper to find intersections between Ethtool link modes, linkmode_intersects(), similar to the other linkmode helpers. Signed-off-by:
-
David S. Miller authored
Merge tag 'wireless-drivers-next-2020-07-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for v5.9 First set of patches for v5.9. This comes later than usual as I was offline for two weeks. The biggest change here is moving Microchip wilc1000 driver from staging. There was an immutable topic branch with one commit moving the whole driver and the topic branch was pulled both to staging-next and wireless-drivers-next. At the moment the only reported conflict is in MAINTAINERS file, so I'm hoping the move should go smoothly. Other notable changes are ath11k getting 6 GHz band support and rtw88 supporting RTL8821CE. And there's also the usual fixes, API changes and cleanups all over. Major changes: wilc1000 * move from drivers/staging to drivers/net/wireless/microchip ath11k * add 6G band support * add spectral scan support iwlwifi * make FW reconfiguration quieter by not using warn level rtw88 * add support for RTL8821CE ==================== Signed-off-by:
-
Christophe JAILLET authored
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below and has been hand modified to replace GFP_ with a correct flag. It has been compile tested. When memory is allocated in 'epic_init_one()' (sis190.c), GFP_KERNEL can be used because this is a net_device_ops' 'ndo_open' function. This function is protected by the rtnl_lock() semaphore. So only a mutex is used and no spin_lock is acquired. When memory is allocated in 'sis900_probe()' (sis900.c), GFP_KERNEL can be used because it is a probe function and no spin_lock is acquired. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Christophe JAILLET authored
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below and has been hand modified to replace GFP_ with a correct flag. It has been compile tested. When memory is allocated in 'r6040_open()', GFP_KERNEL can be used because this is a net_device_ops' 'ndo_open' function. This function is protected by the rtnl_lock() semaphore. So only a mutex is used and no spin_lock is acquired. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Christophe JAILLET authored
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below and has been hand modified to replace GFP_ with a correct flag. It has been compile tested. When memory is allocated in 'hamachi_init_one()' (hamachi.c), GFP_KERNEL can be used because it is a probe function and no lock is acquired. When memory is allocated in 'yellowfin_init_one()' (yellowfin.c), GFP_KERNEL can be used because it is a probe function and no lock is acquired. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by:
-
Christoph Hellwig authored
Most of the tree only uses and implements csum_partial_copy_nocheck, but the c6x and lib/checksum.c implement a csum_partial_copy that isn't used anywere except to define csum_partial_copy. Get rid of this pointless alias. Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Zhang Changzhong authored
Because clk_prepare_enable and clk_disable_unprepare already checked NULL clock parameter, so the additional checks are unnecessary, just remove them. Signed-off-by:
Zhang Changzhong <zhangchangzhong@huawei.com> Signed-off-by:
-
David S. Miller authored
Nicolas Ferre says: ==================== net: macb: Wake-on-Lan magic packet GEM and MACB handling Here is the second part of support for WoL magic-packet on the current macb driver. This one is addressing the bulk of the feature and is based on current net-next/master. MACB and GEM code must co-exist and as they don't share exactly the same register layout, I had to specialize a bit the suspend/resume paths and plug a specific IRQ handler in order to avoid overloading the "normal" IRQ hot path. These changes were tested on both sam9x60 which embeds a MACB+FIFO controller and sama5d2 which has a GEM+packet buffer type of controller. Best regards, Nicolas Changes in v7: - Release the spinlock before exiting macb_suspend/resume in case of error changing IRQ handler Changes in v6: - rebase on net-next/master now that the "fixes" patches of the series are merged in both net and net-next. - GEM addition and MACB update to finish the support of WoL magic-packet on the two revisions of the controller. ==================== Signed-off-by: -
Nicolas Ferre authored
Handle the Wake-on-Lan interrupt for the Cadence MACB Ethernet controller. As we do for the GEM version, we handle of WoL interrupt in a specialized interrupt handler for MACB version that is positionned just between suspend() and resume() calls. Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Harini Katakam <harini.katakam@xilinx.com> Signed-off-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by:
-
Nicolas Ferre authored
Adapt the Wake-on-Lan feature to the Cadence GEM Ethernet controller. This controller has different register layout and cannot be handled by previous code. We disable completely interrupts on all the queues but the queue 0. Handling of WoL interrupt is done in another interrupt handler positioned depending on the controller version used, just between suspend() and resume() calls. It allows to lower pressure on the generic interrupt hot path by removing the need to handle 2 tests for each IRQ: the first figuring out the controller revision, the second for actually knowing if the WoL bit is set. Queue management in suspend()/resume() functions inspired from RFC patch by Harini Katakam <harinik@xilinx.com>, thanks! Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Harini Katakam <harini.katakam@xilinx.com> Signed-off-by:
-
Jiri Pirko authored
In case the qdisc_match_from_root function() is called from non-rcu path with rtnl mutex held, a suspiciout rcu usage warning appears: [ 241.504354] ============================= [ 241.504358] WARNING: suspicious RCU usage [ 241.504366] 5.8.0-rc4-custom-01521-g72a7c7d549c3 #32 Not tainted [ 241.504370] ----------------------------- [ 241.504378] net/sched/sch_api.c:270 RCU-list traversed in non-reader section!! [ 241.504382] other info that might help us debug this: [ 241.504388] rcu_scheduler_active = 2, debug_locks = 1 [ 241.504394] 1 lock held by tc/1391: [ 241.504398] #0: ffffffff85a27850 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x49a/0xbd0 [ 241.504431] stack backtrace: [ 241.504440] CPU: 0 PID: 1391 Comm: tc Not tainted 5.8.0-rc4-custom-01521-g72a7c7d549c3 #32 [ 241.504446] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014 [ 241.504453] Call Trace: [ 241.504465] dump_stack+0x100/0x184 [ 241.504482] lockdep_rcu_suspicious+0x153/0x15d [ 241.504499] qdisc_match_from_root+0x293/0x350 Fix this by passing the rtnl held lockdep condition down to hlist_for_each_entry_rcu() Reported-by:Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
- 20 Jul, 2020 7 commits
-
-
Wang Hai authored
Fix sparse build warning: drivers/net/ethernet/amazon/ena/ena_netdev.c:2193:34: warning: Using plain integer as NULL pointer Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Wang Hai <wanghai38@huawei.com> Suggested-by:
Joe Perches <joe@perches.com> Acked-by:
Shay Agroskin <shayagr@amazon.com> Acked-by:
-
Xu Wang authored
This patch is to use eth_broadcast_addr() to assign broadcast address insetad of memset(). Signed-off-by:
Xu Wang <vulab@iscas.ac.cn> Signed-off-by:
-
David S. Miller authored
Florian Fainelli says: ==================== net: dsa: Setup dsa_netdev_ops This patch series addresses the overloading of a DSA CPU/management interface's netdev_ops for the purpose of providing useful information from the switch side. Up until now we had duplicated the existing netdev_ops structure and added specific function pointers to return information of interest. Here we have a more controlled way of doing this by involving the specific netdev_ops function pointers that we want to be patched, which is easier for auditing code in the future. As a byproduct we can now maintain netdev_ops pointer comparisons which would be failing before (no known in tree problems because of that though). Let me know if this approach looks reasonable to you and we might do the same with our ethtool_ops overloading as well. Changes in v2: - use static inline int vs. static int inline (Kbuild robot) - fixed typos in patch 4 (Andrew) - avoid using macros (Andrew) ==================== Signed-off-by: -
Florian Fainelli authored
Now that we have all the infrastructure in place for calling into the dsa_ptr->netdev_ops function pointers, install them when we configure the DSA CPU/management interface and tear them down. The flow is unchanged from before, but now we preserve equality of tests when network device drivers do tests like dev->netdev_ops == &foo_ops which was not the case before since we were allocating an entirely new structure. Signed-off-by:
-
Florian Fainelli authored
Make the core net_device code call into our ndo_do_ioctl() and ndo_get_phys_port_name() functions via the wrappers defined previously Signed-off-by:
-
Florian Fainelli authored
Add definitions for the dsa_netdevice_ops structure which is a subset of the net_device_ops structure for the specific operations that we care about overlaying on top of the DSA CPU port net_device and provide inline stubs that take core managing whether DSA code is reachable. Signed-off-by:
-
Florian Fainelli authored
In preparation for adding another layer of call into a DSA stacked ops singleton, wrap the ndo_do_ioctl() call into dev_do_ioctl(). Reviewed-by:
-
