- 31 Oct, 2018 32 commits
-
-
José Roberto de Souza authored
It is only used by eDP ports so no need to initialize it for each DP port. Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
José Roberto de Souza <jose.souza@intel.com> Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181030215750.28213-4-jose.souza@intel.com
-
José Roberto de Souza authored
Otherwise it would be in a inconsistent state as port is disconnected but with a valid tc type. Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by:
-
José Roberto de Souza authored
Otherwise it would be in a inconsistent state as port is disconnected but with a valid tc type. Also setting it to unknown will earlier return icl_tc_phy_disconnect() for any future calls to intel_digital_port_connected(), this way we don't need to check if port is marked as safe everytime. Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by:
-
José Roberto de Souza authored
Besides of give the expected output of i915_display_info it will also avoid some aux ch transactions that would timeout by obvious reasons. Reviewed-by:
-
Ville Syrjälä authored
Let's not leak obj->framebuffer_references when we decide that the framebuffer domensions are not suitable for NV12. Cc: stable@vger.kernel.org Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Vidya Srinivas <vidya.srinivas@intel.com> Fixes: e44134f2 ("drm/i915: Add NV12 support to intel_framebuffer_init") Signed-off-by:
Matt Roper <matthew.d.roper@intel.com>
-
Ville Syrjälä authored
Use intel_panel_actually_set_backlight() instead of a direct call to pwm_config() in pwm_disable_backlight(). The main benefit is consistent debug logging when we turn off the backlight. Currently we see nothing in dmesg which made me wonder whether the backlight was even getting turned off properly. The second benefit is consistency; This is what we do for all the other backlight implementations. Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Acked-by:
Jani Nikula <jani.nikula@intel.com>
-
Manasi Navare authored
DP 1.4 spec defines DP secondary data packet for DSC picture parameter set. This patch defines its payload size according to the DP 1.4 specification. Signed-off-by:
Manasi Navare <manasi.d.navare@intel.com> Cc: dri-devel@lists.freedesktop.org Cc: Gaurav K Singh <gaurav.k.singh@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through drm-intel) Reviewed-by:
Harry Wentland <harry.wentland@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-7-manasi.d.navare@intel.com
-
Manasi Navare authored
When DSC is supported we need to validate the modes based on the maximum supported compressed BPP and maximum supported slice count. This allows us to allow the modes with pixel clock greater than the available link BW as long as it meets the compressed BPP and slice count requirements. v3: * Use the macro for dsc sink support (Jani N) v2: * Properly comment why we are right shifting the bpp value (Anusha) Cc: Gaurav K Singh <gaurav.k.singh@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Signed-off-by:
Anusha Srivatsa <anusha.srivatsa@intel.com> Reviewed-by:
Gaurav K Singh <gaurav.k.singh@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-6-manasi.d.navare@intel.com
-
Manasi Navare authored
This patch adds helpers for calculating the maximum compressed BPP supported with small joiner. This also adds a helper for calculating the slice count in case of small joiner. These are inside intel_dp since they take into account hardware limitations. v6: * Take mode_clock and mode_hdisplay as input arguments so that this can be called in intel_dp_mode_valid (Manasi) v5: * Get the max slice width from DPCD * Check against Min_Slice_width of 2560 (Anusha) v4: * #defines for PPR in slice count helper (Gaurav) v3: * Simply logic for bpp (DK) * Limit the valid slice count by max supported by Sink (Manasi) v2: * Change the small joiner RAM buffer constant as bspec changed (Manasi) * rename it as SMALL_JOINER since we are not enabling big joiner yet (Anusha) Cc: Gaurav K Singh <gaurav.k.singh@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Signed-off-by:
-
Manasi Navare authored
This patch adds inline functions and helpers for obtaining DP sink's supported DSC parameters like DSC sink support, eDP compressed BPP supported, maximum slice count supported by the sink devices, DSC line buffer bit depth supported on DP sink, DSC sink maximum color depth by parsing corresponding DPCD registers. v4: * Add helper to give line buf bit depth (Manasi) * Correct the bit masking in color depth helper (manasi) v3: * Use SLICE_CAP_2 for DP (Anusha) v2: * Add DSC sink support macro (Jani N) Cc: Gaurav K Singh <gaurav.k.singh@intel.com> Cc: dri-devel@lists.freedesktop.org Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Signed-off-by:
-
Manasi Navare authored
DSC is supported on eDP starting GEN 10 display (on GLK) and on DP starting GEN 11. This patch implements the discovery phase of DSC. On hotplug, source reads the DSC DPCD register set (0x00060 - 0x0006F) to read the decompression capabilities of the sink device. This entire block of registers is cached in intel_dp so that capability information can be used during DSC configuration phase during compute_config phase of the modeset. For eDP, this caching happens during the eDP initialization. This caching is done only for eDP and DP rev >= 1.4 v5: * Fix the block comment (Gaurav) * Fix the commit message DSC DPCD addresses (Gaurav) * Use DRM_ERROR for dpcd_read fail (Gaurav,Anusha) v4: * Cache these only for Gen >= 11 v3: * Remove the dsc_sink_support field in intel_dp (Jani N) v2: * Clear the cached registers on hotplug always (Jani N) * Combine the eDP and DP caching in same function (Jani N) Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Cc: Gaurav K Singh <gaurav.k.singh@intel.com> Signed-off-by:
-
Manasi Navare authored
This patch defines the DP DSC receiver capability size that gives total number of DP DSC DPCD registers. This also adds a missing #defines for DP DSC support missed in the commit id (ab6a46ea "Add DPCD definitions for DP 1.4 DSC feature") v3: * MIN_SLICE_WIDTH = 2560 (Anusha) * Define DP_DSC_SLICE_WIDTH_MULTIPLIER = 320 v2: * Add SHIFT define and DECOMPRESSION_EN define missed in prev patch Cc: dri-devel@lists.freedesktop.org Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Cc: Gaurav K Singh <gaurav.k.singh@intel.com> Signed-off-by:
-
Anusha Srivatsa authored
Add the newly added slice_row_per_frame parameter in the Picture Parameter Set registers. This defines the number of vertically stacked slices in a frame. Credits to Manasi for noticing bSpec change. Suggested-by:
-
Madhav Chauhan authored
Program the timeout values (in escape clock) for HS TX, LP RX and TA timeout. HX TX: Ensure that host does not continuously transmit in the HS state. If this timer expires, then host will gracefully end its HS transmission and allow the link to enter into LP state. LP RX: Monitor the length of LP receptions from Peripheral. If timeout happens then host will drive the stop state onto all data lanes (only Data Lane 0 should be receiving anything from the Peripheral). This effectively takes back ownership of the bus transmit in the HS state. TA timeout: Timeout valuefor monitoring Bus Turn-Around (BTA) sequence. BTA sequence should complete within a bounded amount of time, with peripheral acknowledging BTA by driving the stop state. v2 by Jani: - Rebase - Use intel_dsi_bitrate() and intel_dsi_tlpx_ns(intel_dsi) - Squash HX TX, LP RX and TA timeout into one patch - Fix bspec mode set sequence reference - Add FIXME about two timeouts Signed-off-by:
Madhav Chauhan <madhav.chauhan@intel.com> Signed-off-by:
-
Madhav Chauhan authored
This patch defines DSI_HTX_TO, DSI_LRX_H_TO, DSI_PWAIT_TO and DSI_TA_TO registers for DSI transcoders '0' and '1'. They are used for contention recovery on DPHY. v2: Define SHIFT for bitfields. v3 by Jani: - Fix timeout bit definitions Signed-off-by:
-
Madhav Chauhan authored
This patch configures mode of combo phy as DDI and disable IO power for DDI ports used by DSI. Signed-off-by:
-
Madhav Chauhan authored
This patch disables both DSI ports by writing to DDI_BUF_CTL registers as part of DSI encoder disable sequence. Signed-off-by:
-
Madhav Chauhan authored
This patch disables portsync mode if DSI link is operating in dual link mode by writing to TRANS_DDI_FUNC_CTL2 registers. Signed-off-by:
-
Madhav Chauhan authored
This patch disables DDI function by writing to TRANS_DDI_FUNC_CTL registers of DSI ports as part of DSI disable sequence. Signed-off-by:
-
Madhav Chauhan authored
As part of DSI disabling sequence, DSI link need to enter in ULPS by writing into DSI_LP_MSG register. This patch does the same using a wrapper function. Signed-off-by:
-
Madhav Chauhan authored
This patch sends command and executes display off, assert reset, power off VBT seqeuences to power down DSI panel. Patch also adds high level function to wrap all the panel sepcific programming during DSI disabling. Signed-off-by:
-
Madhav Chauhan authored
This patch disables transcoders by writing to TRANS_CONF registers for each DSI ports. v2 by Jani: - Wait for pipeconf active to go low Signed-off-by:
-
Madhav Chauhan authored
This patch disbles backlight of DSI panel by using VBT BACKLIGHT_OFF sequence and panel specific disable functions. Signed-off-by:
-
Madhav Chauhan authored
This patch enables backlight of DSI panel by using VBT BACKLIGHT_ON sequence and panel specific functions. Signed-off-by:
-
Madhav Chauhan authored
Driver needs payload/header credits for sending any command and data over DSI link. These credits are released once command or data sent to link. This patch adds functions to wait for releasing of payload and header credits. As per BSPEC, driver needs to ensure that all of commands/data has been dispatched to panel before the transcoder is enabled. This patch implement those steps i.e. sending NOP DCS command, wait for header/payload credit to be released etc. v2 by Jani: - squash the credit wait helpers patch with the first user - pass dev_priv to the credit wait helpers - bikeshed credit helper names - wait for *at least* the current maximum number of credits - indentation fix - add helpers for credits available Signed-off-by:
-
Jonathan Gray authored
Commit b2441318 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license") added "SPDX-License-Identifier: GPL-2.0" to files which previously had no license, change this to MIT for intel_ringbuffer.h matching the license text of intel_ringbuffer.c. Signed-off-by:
Jonathan Gray <jsg@jsg.id.au> Reviewed-by:
-
Madhav Chauhan authored
This patch execute poweron, deassert reset, display on VBT sequences and send TURN_ON DSI command to panel for powering it up. Signed-off-by:
-
Madhav Chauhan authored
This patch programs maximum size of the payload transmitted from peripheral back to the host processor using short packet as a part of panel programming. v2: Rebase v3 by Jani: - Add FIXME note. Signed-off-by:
-
Madhav Chauhan authored
Move DSI connector functions to intel_dsi.c and make them available to both legacy and ICL DSI. v2 by Jani: - Move the functions to intel_dsi.c - Don't reuse intel_dsi_connector_destroy() Signed-off-by:
-
Madhav Chauhan authored
This patch moves intl_dsi_host_init() code to intel_dsi.c so that legacy and gen11 DSI code can share this code. v2 by Jani: - Move the shared stuff to intel_dsi.c Signed-off-by:
-
Matthew Auld authored
When using softpin it's not enough to just pad the vma size, we also need to ensure the vma offset is at the start of the pt boundary, if we plan to utilize 64K pages. Therefore to improve test coverage we should use both aligned and unaligned gtt offsets in igt_write_huge. Suggested-by:
Matthew Auld <matthew.auld@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
-
Hang Yuan authored
This reverts commit c9e66688. Checked GVT codes that guest PPGTT PTE flag bits are propagated to shadow PTE. Read/write bit is not changed. Further tested by i915 self-test case "igt_ctx_readonly". No error or GPU hang was detected. So enable read-only support under GVT. Signed-off-by:
Hang Yuan <hang.yuan@linux.intel.com> Acked-by:
Zhenyu Wang <zhenyuw@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/1540883281-11359-1-git-send-email-hang.yuan@linux.intel.comAcked-by:
-
- 30 Oct, 2018 4 commits
-
-
Animesh Manna authored
ICL supports DC5, DC6, and DC9. Enable DC9 during screen-off, and enable DC5/6 when appropriate. v2: (James Ausmus) - Also handle ICL as GEN9_LP in i915_drm_suspend_late and i915_drm_suspend_early - Add DC9 to gen9_dc_mask for ICL - Re-order GEN checks for newest platform first - Use INTEL_GEN instead of INTEL_INFO->gen - Use INTEL_GEN >= 11 instead of IS_ICELAKE - Consolidate GEN checks v3: (James Ausmus) - Also allow DC6 for ICL (Imre, Art) - Simplify !(GEN >= 11) to GEN < 11 (Imre) v4: (James Ausmus) - Don't call intel_power_sequencer_reset after DC9 for Gen11+, as the PPS regs are Always On - Rebase against upstream changes v5: (Anusha Srivatsa) - rebased against the latest upstream changes. v6: (Anusha Srivatsa) - rebased.Use INTEL_GEN consistently. - Simplify the code (Rodrigo) v7: rebased. Change order according to platforms(Jyoti) v8: rebased. Change the check from platform specific to HAS_PCH_SPLIT(). Add comment in code to be more clear.(Rodrigo) Cc: Imre Deak <imre.deak@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
Animesh Manna <animesh.manna@intel.com> Signed-off-by:
James Ausmus <james.ausmus@intel.com> Signed-off-by:
Jyoti Yadav <jyoti.r.yadav@intel.com> Reviewed-by:
-
Chris Wilson authored
If we reduce the suspend function for intel_opregion to do the minimum required, the resume function can also do the simple task of notifier the ACPI bios that we are back. This avoid some nasty restrictions on the likes of register_acpi_notifier() that are not allowed during the early phase of resume. v2: Keep the order of acpi notify vs turning off ardy/drdy the same. Signed-off-by:
Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181030110554.4111-1-chris@chris-wilson.co.uk
-
Chris Wilson authored
If we can prevent stray writes from landing in the scratch page, we can reuse the same page and same scratch PT for all contexts without fear of information leaks and side-channels. Signed-off-by:
-
Chris Wilson authored
Record the scratch PTE encoding upon creation rather than recomputing the bits everytime. This is important for the next patch where we forgo having a valid scratch page with which we may compute the bits and so require keeping the PTE value instead. v2: Fix up scrub_64K to use scratch_pte as well. Signed-off-by:
-
- 29 Oct, 2018 4 commits
-
-
Dhinakaran Pandiyan authored
intel_fb_pitch_limit() has the parameters pixel_format and fb_modifier switched in their positions. The parameters are however used correctly, but change the order for consistency. Also use kernel data types for both parameters. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Reviewed-by:
-
Dhinakaran Pandiyan authored
The PLANE_AUX_OFFSET mmio does not exist on ICL, do not program it. We'll still calculate the aux offset as it is required for adjusing x-y offsets. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by:
-
Dhinakaran Pandiyan authored
A framebuffer can comprise surfaces with distinct tiling formats, making checks against modifier alone insufficient. Make use of a function to identify a linear surface based on both modifier and color plane. v2: Typo fix v3: remove 'inline' from function definition (Ville) Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Dhinakaran Pandiyan authored
The bits weren't defined in descending order. v2: Move definitions in a separate patch (Manasi) Cc: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
-
