Centralise the PHY interface mode switching, rather than having it in
two places.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add reporting of the MDI swap to the Marvell 10G PHY driver by providing
a generic implementation for the standard 10GBASE-T pair swap register
and polarity register.  We also support reading the MDI swap status for
1G and below from a PCS register.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update header comments to indicate the newly found behaviour with XAUI
interfaces.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The locate operation interface of fiber port can only
work with DT mode. Add a new interface to control the
locate led for ACPI mode.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Tested-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the check for setting  IPV4 filters and align filter_id
to multiple of 2, only for IPv6 filters in case of T6.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Netanel Belgazal says:

====================
update ENA driver to version 1.5.0

This patchset contains two changes:
* Add a robust mechanism for detection of stuck Rx/Tx rings due to
  missed or misrouted MSI-X
* Increase the driver version to 1.5.0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A mechanism for detection of stuck Rx/Tx rings due to missed or
misrouted interrupts.
Check if there are unhandled completion descriptors before the first
MSI-X interrupt arrived.
The check is per queue and per interrupt vector.
Once such condition is detected, driver and device reset is scheduled.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Masami Hiramatsu says:

====================
net: tcp: sctp: dccp: Replace jprobe usage with trace events

This series is v7 of the replacement of jprobe usage with trace
events. This version fixes net/dccp/trace.h to avoid sparse
warning. Since the TP_STORE_ADDR_PORTS macro can be shared
with trace/events/tcp.h, it also introduce a new common header
file and move the definition of that macro.

Previous version is here;
 https://lkml.org/lkml/2017/12/28/7

Changes from v6:
  [5/6]: Avoid preprocessor directives in tracepoint macro args
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove DCCP probe module since jprobe has been deprecated.
That function is now replaced by dccp/dccp_probe trace-event.
You can use it via ftrace or perftools.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add DCCP sendmsg trace event (dccp/dccp_probe) for
replacing dccpprobe. User can trace this event via
ftrace or perftools.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove SCTP probe module since jprobe has been deprecated.
That function is now replaced by sctp/sctp_probe and
sctp/sctp_probe_path trace-events.
You can use it via ftrace or perftools.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add SCTP ACK tracking trace event to trace the changes of SCTP
association state in response to incoming packets.
It is used for debugging SCTP congestion control algorithms,
and will replace sctp_probe module.

Note that this event a bit tricky. Since this consists of 2
events (sctp_probe and sctp_probe_path) so you have to enable
both events as below.

  # cd /sys/kernel/debug/tracing
  # echo 1 > events/sctp/sctp_probe/enable
  # echo 1 > events/sctp/sctp_probe_path/enable

Or, you can enable all the events under sctp.

  # echo 1 > events/sctp/enable

Since sctp_probe_path event is always invoked from sctp_probe
event, you can not see any output if you only enable
sctp_probe_path.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove TCP probe module since jprobe has been deprecated.
That function is now replaced by tcp/tcp_probe trace-event.
You can use it via ftrace or perftools.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds an event to trace TCP stat variables with
slightly intrusive trace-event. This uses ftrace/perf
event log buffer to trace those state, no needs to
prepare own ring-buffer, nor custom user apps.

User can use ftrace to trace this event as below;

  # cd /sys/kernel/debug/tracing
  # echo 1 > events/tcp/tcp_probe/enable
  (run workloads)
  # cat trace
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tomer Tayar says:

====================
qed*: Advance to FW 8.33.1.0

This series advances all qed* drivers to use firmware 8.33.1.0 which brings
new capabilities and initial support of new HW. The changes are mostly in
qed, and include changes in the FW interface files, as well as updating the
FW initialization and debug collection code. The protocol drivers have
minor functional changes for this firmware.

Patch 1 Rearranges and refactors the FW interface files in preparation of
the new FW (no functional change).
Patch 2 Prepares the code for support of new HW (no functional change).
Patch 3 Actual utilization of the new FW.
Patch 4 Advances drivers' version.

v3->v4:
Fix a compilation issue which was reported by krobot (dependency on CRC8).

v2->v3:
Resend the series with a fixed title in the cover letter.

v1->v2:
- Break the previous single patch into several patches.
- Fix compilation issues which were reported by krobot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Advance the qed* drivers to use firmware 8.33.1.0:
Modify core driver (qed) to utilize the new FW and initialize the device
with it. This is the lion's share of the patch, and includes changes to FW
interface files, device initialization flows, FW interaction flows, and
debug collection flows.
Modify Ethernet driver (qede) to make use of new FW in fastpath.
Modify RoCE/iWARP driver (qedr) to make use of new FW in fastpath.
Modify FCoE driver (qedf) to make use of new FW in fastpath.
Modify iSCSI driver (qedi) to make use of new FW in fastpath.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Bason <Yuval.Bason@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Manish Chopra <Manish.Chopra@cavium.com>
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch renames defines and structures in the FW HSI files to allow a
distinction between different types of HW.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch refactors and reorders the FW API files in preparation of
upgrading the code to support new FW.

- Make use of the BIT macro in appropriate places.
- Whitespace changes to align values and code blocks.
- Comments are updated (spelling mistakes, removed if not clear).
- Group together code blocks which are related or deal with similar
 matters.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

inet_diag currently provides less/greater than or equal operators for
comparing ports when filtering sockets. An equal comparison can be
performed by combining the two existing operators, or a user can for
example request a port range and then do the final filtering in
userspace. However, these approaches both have drawbacks. Implementing
equal using LE/GE causes the size and complexity of a filter to grow
quickly as the number of ports increase, while it on busy machines would
be great if the kernel only returns information about relevant sockets.

This patch introduces source and destination port equal operators.
INET_DIAG_BC_S_EQ is used to match a source port, INET_DIAG_BC_D_EQ a
destination port, and usage is the same as for the existing port
operators.  I.e., the port to match is stored in the no-member of the
next inet_diag_bc_op-struct in the filter.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: updates 2017-12-27

please apply some post-christmas leftovers for 4.16.
Two patches to improve IP address management on L3, and two that add
support to auto-config the transport mode on z/VM VNICs.
Note that one patch in the series touches arch/s390 (acked by Martin).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The transport mode that a z/VM NIC is configured in, must match the
hypervisor-internal network which the NIC is coupled to.

To get this right automatically, have qeth issue a diag26c hypervisor call
that provides all sorts of information for a specific VNIC.
With z/VM update VM65918, this also includes the VNIC's required
transport mode.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With subcode 0x24, diag26c returns all sorts of VNIC-related information.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

By parameterising the address type, we need just one helper that walks
the IP table and builds up the response string.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When adding & removing IP entries for rxip/vipa/ipato/hsuid, forward any
resulting errors back to the sysfs-level caller.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

OVS_NLERR prints a newline at the end of the message string, so the
message string does not need to include a newline explicitly.  Done
using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

DCCP_CRIT prints some other text and then a newline after the message
string, so the message string does not need to include a newline
explicitly.  Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

When dev_requeue_skb() is called with bulked skb list, only the
first skb of the list will be requeued to qdisc layer, and leak
the others without free them.

TCP is broken due to skb leak since no free skb will be considered
as still in the host queue and never be retransmitted. This happend
when dev_requeue_skb() called from qdisc_restart().
  qdisc_restart
  |-- dequeue_skb
  |-- sch_direct_xmit()
      |-- dev_requeue_skb() <-- skb may bluked

Fix dev_requeue_skb() to requeue the full bluked list. Also change
to use __skb_queue_tail() in __dev_requeue_skb() to avoid skb out
of order.

Fixes: a53851e2 ("net: sched: explicit locking in gso_cpu fallback")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On T6, LIP compression is always enabled for IPv6 and uncompressed
IPv6 for LIP is not supported. So, for IPv6 TCAM filters on T6,
add LIP6 to CLIP on filter creation, and release the same on filter
deletion.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add test cases for ipv4, ipv6 erspan, v1 and v2 native mode
and external (collect metadata) mode.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the rx fastpath, the function netdev_alloc_skb rarely fails.
Therefore, a likely() optimization is added to this error check
conditional.

CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Address/port initialization should work correctly regardless
of the order in which command line arguments are supplied,
E.g, cfg_port should be used to connect to the remote host
even if it is processed after -D, src/dst address initialization
should not require that [-4|-6] be specified before
the -S or -D args, receiver should be able to bind to *.<cfg_port>

Achieve this by making sure that the address/port structures
are initialized after all command line options are parsed.

Store cfg_port in host-byte order, and use htons()
to set up the sin_port/sin6_port before bind/connect,
so that the network system calls get the correct values
in network-byte order.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nogah Frankel says:

====================
net: sched: Fix RED qdisc offload flag

Replacing the RED offload flag (TC_RED_OFFLOADED) with the generic one
(TCQ_F_OFFLOADED) deleted some of the logic behind it. This patchset fixes
this problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the check of the offload state to after the qdisc dump action was
called, so the qdisc could update it if it was changed.

Fixes: 7a4fa291 ("net: sched: Add TCA_HW_OFFLOAD")
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the offload flag, TCQ_F_OFFLOADED, in each dump call (and ignore
the offloading function return value in relation to this flag).
This is done because a qdisc is being initialized, and therefore offloaded
before being grafted. Since the ability of the driver to offload the qdisc
depends on its location, a qdisc can be offloaded and un-offloaded by graft
calls, that doesn't effect the qdisc itself.

Fixes: 428a68af ("net: sched: Move to new offload indication in RED"
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2_vpd_wait is not called in an interrupt handler nor holding a spinlock.
The function mdelay in it can be replaced with msleep, to reduce busy wait.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When running consumer and/or producer operations and empty checks in
parallel its possible to have the empty check run past the end of the
array. The scenario occurs when an empty check is run while
__ptr_ring_discard_one() is in progress. Specifically after the
consumer_head is incremented but before (consumer_head >= ring_size)
check is made and the consumer head is zeroe'd.

To resolve this, without having to rework how consumer/producer ops
work on the array, simply add an extra dummy slot to the end of the
array. Even if we did a rework to avoid the extra slot it looks
like the normal case checks would suffer some so best to just
allocate an extra pointer.
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Fixes: c5ad119f ("net: sched: pfifo_fast use skb_array")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/ipv6/ip6_gre.c is a case of parallel adds.

include/trace/events/tcp.h is a little bit more tricky.  The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) IPv6 gre tunnels end up with different default features enabled
    depending upon whether netlink or ioctls are used to bring them up.
    Fix from Alexey Kodanev.

 2) Fix read past end of user control message in RDS< from Avinash
    Repaka.

 3) Missing RCU barrier in mini qdisc code, from Cong Wang.

 4) Missing policy put when reusing per-cpu route entries, from Florian
    Westphal.

 5) Handle nested PCI errors properly in bnx2x driver, from Guilherme G.
    Piccoli.

 6) Run nested transport mode IPSEC packets via tasklet, from Herbert
    Xu.

 7) Fix handling poll() for stream sockets in tipc, from Parthasarathy
    Bhuvaragan.

 8) Fix two stack-out-of-bounds issues in IPSEC, from Steffen Klassert.

 9) Another zerocopy ubuf handling fix, from Willem de Bruijn.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
  strparser: Call sock_owned_by_user_nocheck
  sock: Add sock_owned_by_user_nocheck
  skbuff: in skb_copy_ubufs unclone before releasing zerocopy
  tipc: fix hanging poll() for stream sockets
  sctp: Replace use of sockets_allocated with specified macro.
  bnx2x: Improve reliability in case of nested PCI errors
  tg3: Enable PHY reset in MTU change path for 5720
  tg3: Add workaround to restrict 5762 MRRS to 2048
  tg3: Update copyright
  net: fec: unmap the xmit buffer that are not transferred by DMA
  tipc: fix tipc_mon_delete() oops in tipc_enable_bearer() error path
  tipc: error path leak fixes in tipc_enable_bearer()
  RDS: Check cmsg_len before dereferencing CMSG_DATA
  tcp: Avoid preprocessor directives in tracepoint macro args
  tipc: fix memory leak of group member when peer node is lost
  net: sched: fix possible null pointer deref in tcf_block_put
  tipc: base group replicast ack counter on number of actual receivers
  net_sched: fix a missing rcu barrier in mini_qdisc_pair_swap()
  net: phy: micrel: ksz9031: reconfigure autoneg after phy autoneg workaround
  ip6_gre: fix device features for ioctl setup
  ...