- 26 Jul, 2013 16 commits
-
-
Axel Lin authored
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Shawn Guo authored
Function lpuart_setup_watermark() clears some bits in register UARTCR2 before writing FIFO configuration registers as required by hardware. But it should restore UARTCR2 after that. Otherwise, we end up changing UARTCR2 register when setting up watermark, and that is not really desirable. At least, when low-level debug and earlyprint is enabled, serial console is broken due to it. Fix the problem by restoring UARTCR2 register at the end of function lpuart_setup_watermark(). Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ruchika Kharwar authored
Ensure the Interrupt handling routine return IRQ_HANDLED vs IRQ_NONE. Signed-off-by: Ruchika Kharwar <ruchika@ti.com> Signed-off-by: Alexander Savchenko <oleksandr.savchenko@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Vikram Pandita authored
Otherwise serial driver would crash accessing platform_data that was not initialized in functions like: serial_omap_pm(...) ... if (!state && pdata->enable_wakeup) ^^^^^^^ ... Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> Signed-off-by: Alexander Savchenko <oleksandr.savchenko@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ruchika Kharwar authored
The revision register is a 32 bit register. The serial_in() function reads only the lower 16 bits of the register. This leads to an incorrect computation of the Module revision. Signed-off-by: Ruchika Kharwar <ruchika@ti.com> [oleksandr.savchenko@ti.com: add some whitespaces] Signed-off-by: Alexander Savchenko <oleksandr.savchenko@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dmitry Fink authored
Current logic results in interrupt storm since the fifo is constantly below the threshold level. Change the logic to fill all the available spaces in the fifo as long as we have data to minimize the possibilty of underflow and elimiate excessive interrupts. Signed-off-by: Dmitry Fink <finik@ti.com> Signed-off-by: Alexander Savchenko <oleksandr.savchenko@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Govindraj.R authored
wer has TX wakeup bit available enable the same by populating the necessary tx wakeup flag for the applicable module ip blocks and use the same while configuaring wer reg. Also wer is not context restored, restore wer when context is lost. Cc: Paul Walmsley <paul@pwsan.com> Cc: Felipe Balbi <balbi@ti.com> Cc: Kevin Hilman <kevin.hilman@linaro.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> (for drivers/tty changes) Signed-off-by: Govindraj.R <govindraj.raja@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Stefan Seyfried authored
The recent regression about NetMos 9835 Multi-I/O boards indicates that comment pointing to the parport_serial driver could be helpful. Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shiyan authored
This patch adds support for MAX14830 (advanced quad universal asynchronous receiver-transmitter) into max310x driver. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shiyan authored
This patch adds support for MAX3109 (advanced dual universal asynchronous receiver-transmitter) into max310x driver. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shiyan authored
This patch rework max310x driver. Major changes have been made: - Prepare driver to support ICs with more than one UART. - Prepare driver to support work with I2C-bus. The patch changes almost every function and can not be divided into parts. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Huang Shijie authored
We only enable the DMA support when the following are meet: [1] The uart port supports the hardware flow control(CTS/RTS). (Some uart port does not support the CTS/RTS.) [2] The application enables the CTS/RTS. [3] The Soc is imx6q. For the sdma's firmware limit, we do not support the DMA except the imx6q platform. [4] The uart is not used as a console. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Hubert Feurstein authored
It was not possible to set custom-baudrates like 62500. Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Huang Shijie authored
We will add the DMA support for the imx uart. For the firmware's limit, only the imx6 serial chips (including the imx6q, imx6dl, imx6sl) can support the DMA. This patch adds the necessary macro and helper to distinguish the imx6q uart from the other imx uart. Other chips can use the "fsl,imx6q-uart" to enable the DMA support. This patch also replaces the check "is_imx21_uart()" with "!is_imx1_uart()". Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Huang Shijie authored
The uart_console() check makes the clocks(clk_per and clk_ipg) opened even when we close the console uart. This patch enable/disable the clocks in imx_console_write(), so we can keep the clocks closed when the console uart is closed. Also remove the clock enable/disable oprations in the probe, we do not need them any more. Signed-off-by: Huang Shijie <b32955@freescale.com> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jingoo Han authored
The driver core clears the driver data to NULL after device_release or on probe failure, since commit 0998d063 (device-core: Ensure drvdata = NULL when no driver is bound). Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Barry Song <baohua.song@csr.com> Acked-by: Tony Prisk <linux@prisktech.co.nz> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 24 Jul, 2013 24 commits
-
-
Hendrik Brueckner authored
Implement the dtr_rts() hvc console callback to improve control when to disconnect the IUCV connection. Previously, the IUCV connection was disconnected during the notifier_del() callback, i.e., when the last file descriptor to the hvc terminal device was closed. Recent changes in login programs caused undesired disconnects during the login phase. To prevent these kind of disconnects, implement the dtr_rts callback to implicitly handle the HUPCL termios control via the hvc_console driver. Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Hendrik Brueckner authored
Introduce a new callback to explicitly handle the HUPCL termios control flag. This prepares for a follow-up commit for the hvc_iucv device driver to improve handling when to drop an established network connection. The callback naming is based on the recently added tty_port interface to facilitate a potential refactoring of the hvc_console to use tty_port functions. Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Wolfram Sang authored
Since commit ab78029e (drivers/pinctrl: grab default handles from device core), we can rely on device core for setting the default pins. Compile tested only. Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Aldo Iljazi authored
Specifically: n_gsm.c:810: ERROR: space required before the open parenthesis '(' n_gsm.c:830: WARNING: line over 80 characters n_gsm.c:971: ERROR: trailing whitespace n_gsm.c:984: ERROR: code indent should use tabs where possible n_gsm.c:984: WARNING: please, no space before tabs n_gsm.c:984: WARNING: please, no spaces at the start of a line n_gsm.c:1141: WARNING: space prohibited before semicolon n_gsm.c:1743: ERROR: space required before the open brace '{' n_gsm.c:1744: WARNING: line over 80 characters n_gsm.c:1745: ERROR: code indent should use tabs where possible n_gsm.c:1746: ERROR: code indent should use tabs where possible n_gsm.c:2908: WARNING: line over 80 characters n_gsm.c:2912: ERROR: trailing whitespace Signed-off-by: Aldo Iljazi <neonsync1@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Commits 6a1c0680 and 9356b535, respectively 'tty: Convert termios_mutex to termios_rwsem' and 'n_tty: Access termios values safely' introduced a circular lock dependency with console_lock and termios_rwsem. The lockdep report [1] shows that n_tty_write() will attempt to claim console_lock while holding the termios_rwsem, whereas tty_do_resize() may already hold the console_lock while claiming the termios_rwsem. Since n_tty_write() and tty_do_resize() do not contend over the same data -- the tty->winsize structure -- correct the lock dependency by introducing a new lock which specifically serializes access to tty->winsize only. [1] Lockdep report ====================================================== [ INFO: possible circular locking dependency detected ] 3.10.0-0+tip-xeon+lockdep #0+tip Not tainted ------------------------------------------------------- modprobe/277 is trying to acquire lock: (&tty->termios_rwsem){++++..}, at: [<ffffffff81452656>] tty_do_resize+0x36/0xe0 but task is already holding lock: ((fb_notifier_list).rwsem){.+.+.+}, at: [<ffffffff8107aac6>] __blocking_notifier_call_chain+0x56/0xc0 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 ((fb_notifier_list).rwsem){.+.+.+}: [<ffffffff810b6d62>] lock_acquire+0x92/0x1f0 [<ffffffff8175b797>] down_read+0x47/0x5c [<ffffffff8107aac6>] __blocking_notifier_call_chain+0x56/0xc0 [<ffffffff8107ab46>] blocking_notifier_call_chain+0x16/0x20 [<ffffffff813d7c0b>] fb_notifier_call_chain+0x1b/0x20 [<ffffffff813d95b2>] register_framebuffer+0x1e2/0x320 [<ffffffffa01043e1>] drm_fb_helper_initial_config+0x371/0x540 [drm_kms_helper] [<ffffffffa01bcb05>] nouveau_fbcon_init+0x105/0x140 [nouveau] [<ffffffffa01ad0af>] nouveau_drm_load+0x43f/0x610 [nouveau] [<ffffffffa008a79e>] drm_get_pci_dev+0x17e/0x2a0 [drm] [<ffffffffa01ad4da>] nouveau_drm_probe+0x25a/0x2a0 [nouveau] [<ffffffff813b13db>] local_pci_probe+0x4b/0x80 [<ffffffff813b1701>] pci_device_probe+0x111/0x120 [<ffffffff814977eb>] driver_probe_device+0x8b/0x3a0 [<ffffffff81497bab>] __driver_attach+0xab/0xb0 [<ffffffff814956ad>] bus_for_each_dev+0x5d/0xa0 [<ffffffff814971fe>] driver_attach+0x1e/0x20 [<ffffffff81496cc1>] bus_add_driver+0x111/0x290 [<ffffffff814982b7>] driver_register+0x77/0x170 [<ffffffff813b0454>] __pci_register_driver+0x64/0x70 [<ffffffffa008a9da>] drm_pci_init+0x11a/0x130 [drm] [<ffffffffa022a04d>] nouveau_drm_init+0x4d/0x1000 [nouveau] [<ffffffff810002ea>] do_one_initcall+0xea/0x1a0 [<ffffffff810c54cb>] load_module+0x123b/0x1bf0 [<ffffffff810c5f57>] SyS_init_module+0xd7/0x120 [<ffffffff817677c2>] system_call_fastpath+0x16/0x1b -> #1 (console_lock){+.+.+.}: [<ffffffff810b6d62>] lock_acquire+0x92/0x1f0 [<ffffffff810430a7>] console_lock+0x77/0x80 [<ffffffff8146b2a1>] con_flush_chars+0x31/0x50 [<ffffffff8145780c>] n_tty_write+0x1ec/0x4d0 [<ffffffff814541b9>] tty_write+0x159/0x2e0 [<ffffffff814543f5>] redirected_tty_write+0xb5/0xc0 [<ffffffff811ab9d5>] vfs_write+0xc5/0x1f0 [<ffffffff811abec5>] SyS_write+0x55/0xa0 [<ffffffff817677c2>] system_call_fastpath+0x16/0x1b -> #0 (&tty->termios_rwsem){++++..}: [<ffffffff810b65c3>] __lock_acquire+0x1c43/0x1d30 [<ffffffff810b6d62>] lock_acquire+0x92/0x1f0 [<ffffffff8175b724>] down_write+0x44/0x70 [<ffffffff81452656>] tty_do_resize+0x36/0xe0 [<ffffffff8146c841>] vc_do_resize+0x3e1/0x4c0 [<ffffffff8146c99f>] vc_resize+0x1f/0x30 [<ffffffff813e4535>] fbcon_init+0x385/0x5a0 [<ffffffff8146a4bc>] visual_init+0xbc/0x120 [<ffffffff8146cd13>] do_bind_con_driver+0x163/0x320 [<ffffffff8146cfa1>] do_take_over_console+0x61/0x70 [<ffffffff813e2b93>] do_fbcon_takeover+0x63/0xc0 [<ffffffff813e67a5>] fbcon_event_notify+0x715/0x820 [<ffffffff81762f9d>] notifier_call_chain+0x5d/0x110 [<ffffffff8107aadc>] __blocking_notifier_call_chain+0x6c/0xc0 [<ffffffff8107ab46>] blocking_notifier_call_chain+0x16/0x20 [<ffffffff813d7c0b>] fb_notifier_call_chain+0x1b/0x20 [<ffffffff813d95b2>] register_framebuffer+0x1e2/0x320 [<ffffffffa01043e1>] drm_fb_helper_initial_config+0x371/0x540 [drm_kms_helper] [<ffffffffa01bcb05>] nouveau_fbcon_init+0x105/0x140 [nouveau] [<ffffffffa01ad0af>] nouveau_drm_load+0x43f/0x610 [nouveau] [<ffffffffa008a79e>] drm_get_pci_dev+0x17e/0x2a0 [drm] [<ffffffffa01ad4da>] nouveau_drm_probe+0x25a/0x2a0 [nouveau] [<ffffffff813b13db>] local_pci_probe+0x4b/0x80 [<ffffffff813b1701>] pci_device_probe+0x111/0x120 [<ffffffff814977eb>] driver_probe_device+0x8b/0x3a0 [<ffffffff81497bab>] __driver_attach+0xab/0xb0 [<ffffffff814956ad>] bus_for_each_dev+0x5d/0xa0 [<ffffffff814971fe>] driver_attach+0x1e/0x20 [<ffffffff81496cc1>] bus_add_driver+0x111/0x290 [<ffffffff814982b7>] driver_register+0x77/0x170 [<ffffffff813b0454>] __pci_register_driver+0x64/0x70 [<ffffffffa008a9da>] drm_pci_init+0x11a/0x130 [drm] [<ffffffffa022a04d>] nouveau_drm_init+0x4d/0x1000 [nouveau] [<ffffffff810002ea>] do_one_initcall+0xea/0x1a0 [<ffffffff810c54cb>] load_module+0x123b/0x1bf0 [<ffffffff810c5f57>] SyS_init_module+0xd7/0x120 [<ffffffff817677c2>] system_call_fastpath+0x16/0x1b other info that might help us debug this: Chain exists of: &tty->termios_rwsem --> console_lock --> (fb_notifier_list).rwsem Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock((fb_notifier_list).rwsem); lock(console_lock); lock((fb_notifier_list).rwsem); lock(&tty->termios_rwsem); *** DEADLOCK *** 7 locks held by modprobe/277: #0: (&__lockdep_no_validate__){......}, at: [<ffffffff81497b5b>] __driver_attach+0x5b/0xb0 #1: (&__lockdep_no_validate__){......}, at: [<ffffffff81497b69>] __driver_attach+0x69/0xb0 #2: (drm_global_mutex){+.+.+.}, at: [<ffffffffa008a6dd>] drm_get_pci_dev+0xbd/0x2a0 [drm] #3: (registration_lock){+.+.+.}, at: [<ffffffff813d93f5>] register_framebuffer+0x25/0x320 #4: (&fb_info->lock){+.+.+.}, at: [<ffffffff813d8116>] lock_fb_info+0x26/0x60 #5: (console_lock){+.+.+.}, at: [<ffffffff813d95a4>] register_framebuffer+0x1d4/0x320 #6: ((fb_notifier_list).rwsem){.+.+.+}, at: [<ffffffff8107aac6>] __blocking_notifier_call_chain+0x56/0xc0 stack backtrace: CPU: 0 PID: 277 Comm: modprobe Not tainted 3.10.0-0+tip-xeon+lockdep #0+tip Hardware name: Dell Inc. Precision WorkStation T5400 /0RW203, BIOS A11 04/30/2012 ffffffff8213e5e0 ffff8802aa2fb298 ffffffff81755f19 ffff8802aa2fb2e8 ffffffff8174f506 ffff8802aa2fa000 ffff8802aa2fb378 ffff8802aa2ea8e8 ffff8802aa2ea910 ffff8802aa2ea8e8 0000000000000006 0000000000000007 Call Trace: [<ffffffff81755f19>] dump_stack+0x19/0x1b [<ffffffff8174f506>] print_circular_bug+0x1fb/0x20c [<ffffffff810b65c3>] __lock_acquire+0x1c43/0x1d30 [<ffffffff810b775e>] ? mark_held_locks+0xae/0x120 [<ffffffff810b78d5>] ? trace_hardirqs_on_caller+0x105/0x1d0 [<ffffffff810b6d62>] lock_acquire+0x92/0x1f0 [<ffffffff81452656>] ? tty_do_resize+0x36/0xe0 [<ffffffff8175b724>] down_write+0x44/0x70 [<ffffffff81452656>] ? tty_do_resize+0x36/0xe0 [<ffffffff81452656>] tty_do_resize+0x36/0xe0 [<ffffffff8146c841>] vc_do_resize+0x3e1/0x4c0 [<ffffffff8146c99f>] vc_resize+0x1f/0x30 [<ffffffff813e4535>] fbcon_init+0x385/0x5a0 [<ffffffff8146a4bc>] visual_init+0xbc/0x120 [<ffffffff8146cd13>] do_bind_con_driver+0x163/0x320 [<ffffffff8146cfa1>] do_take_over_console+0x61/0x70 [<ffffffff813e2b93>] do_fbcon_takeover+0x63/0xc0 [<ffffffff813e67a5>] fbcon_event_notify+0x715/0x820 [<ffffffff81762f9d>] notifier_call_chain+0x5d/0x110 [<ffffffff8107aadc>] __blocking_notifier_call_chain+0x6c/0xc0 [<ffffffff8107ab46>] blocking_notifier_call_chain+0x16/0x20 [<ffffffff813d7c0b>] fb_notifier_call_chain+0x1b/0x20 [<ffffffff813d95b2>] register_framebuffer+0x1e2/0x320 [<ffffffffa01043e1>] drm_fb_helper_initial_config+0x371/0x540 [drm_kms_helper] [<ffffffff8173cbcb>] ? kmemleak_alloc+0x5b/0xc0 [<ffffffff81198874>] ? kmem_cache_alloc_trace+0x104/0x290 [<ffffffffa01035e1>] ? drm_fb_helper_single_add_all_connectors+0x81/0xf0 [drm_kms_helper] [<ffffffffa01bcb05>] nouveau_fbcon_init+0x105/0x140 [nouveau] [<ffffffffa01ad0af>] nouveau_drm_load+0x43f/0x610 [nouveau] [<ffffffffa008a79e>] drm_get_pci_dev+0x17e/0x2a0 [drm] [<ffffffffa01ad4da>] nouveau_drm_probe+0x25a/0x2a0 [nouveau] [<ffffffff8175f162>] ? _raw_spin_unlock_irqrestore+0x42/0x80 [<ffffffff813b13db>] local_pci_probe+0x4b/0x80 [<ffffffff813b1701>] pci_device_probe+0x111/0x120 [<ffffffff814977eb>] driver_probe_device+0x8b/0x3a0 [<ffffffff81497bab>] __driver_attach+0xab/0xb0 [<ffffffff81497b00>] ? driver_probe_device+0x3a0/0x3a0 [<ffffffff814956ad>] bus_for_each_dev+0x5d/0xa0 [<ffffffff814971fe>] driver_attach+0x1e/0x20 [<ffffffff81496cc1>] bus_add_driver+0x111/0x290 [<ffffffffa022a000>] ? 0xffffffffa0229fff [<ffffffff814982b7>] driver_register+0x77/0x170 [<ffffffffa022a000>] ? 0xffffffffa0229fff [<ffffffff813b0454>] __pci_register_driver+0x64/0x70 [<ffffffffa008a9da>] drm_pci_init+0x11a/0x130 [drm] [<ffffffffa022a000>] ? 0xffffffffa0229fff [<ffffffffa022a000>] ? 0xffffffffa0229fff [<ffffffffa022a04d>] nouveau_drm_init+0x4d/0x1000 [nouveau] [<ffffffff810002ea>] do_one_initcall+0xea/0x1a0 [<ffffffff810c54cb>] load_module+0x123b/0x1bf0 [<ffffffff81399a50>] ? ddebug_proc_open+0xb0/0xb0 [<ffffffff813855ae>] ? trace_hardirqs_on_thunk+0x3a/0x3f [<ffffffff810c5f57>] SyS_init_module+0xd7/0x120 [<ffffffff817677c2>] system_call_fastpath+0x16/0x1b Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Acquiring the write_wait queue spin lock now accounts for the largest slice of cpu time on the tty write path. Two factors contribute to this situation; a overly-pessimistic line discipline write loop which _always_ sets up a wait loop even if i/o will immediately succeed, and on ptys, a wakeup storm from reads and writes. Writer wakeup does not need to be performed by the pty driver. Firstly, since the actual i/o is performed within the write, the line discipline write loop will continue while space remains in the flip buffers. Secondly, when space becomes avail in the line discipline receive buffer (and thus also in the flip buffers), the pty unthrottle re-wakes the writer (non-flow-controlled line disciplines unconditionally unthrottle the driver when data is received). Thus, existing in-kernel i/o is guaranteed to advance. Finally, writer wakeup occurs at the conclusion of the line discipline write (in tty_write_unlock()). This guarantees that any user-space write waiters are woken to continue additional i/o. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
LNEXT processing accounts for ~15% of total cpu time in end-to-end tty i/o; factor the lnext test/clear from the per-char i/o path. Instead, attempt to immediately handle the literal next char if not at the end of this received buffer; otherwise, handle the first char of the next received buffer as the literal next char, then continue with normal i/o. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
gcc will likely inline these single-use functions anyway; remove inline modifier. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Always pre-figure the space available in the read_buf and limit the inbound receive request to that amount. For compatibility reasons with the non-flow-controlled interface, n_tty_receive_buf() will continue filling read_buf until all data has been received or receive_room() returns 0. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Handle PARMRK processing on the slow per-char i/o path. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Convert to modal receive_buf processing; factor char receive processing for unusual termios settings out of normal per-char i/o path. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Factor 'special' per-char processing into standalone fn, n_tty_receive_char_special(), which handles processing for chars marked in the char_map. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Relocate the IXANY restart tty test to code paths where the the received char is not START_CHAR, STOP_CHAR, INTR_CHAR, QUIT_CHAR or SUSP_CHAR. Fixes the condition when ISIG if off and one of INTR_CHAR, QUIT_CHAR or SUSP_CHAR does not restart i/o. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Simplify __receive_buf() into a dispatch function; perform per-char processing for all other modes not already handled. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Commit 20bafb3d 'n_tty: Move buffers into n_tty_data' broke the ppc64 build. Include vmalloc.h for the required function declarations. Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Convert to modal receive_buf() processing; factor receive char processing when tty->closing into n_tty_receive_buf_closing(). Note that EXTPROC when ISTRIP or IUCLC is set continues to be handled by n_tty_receive_char(). Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
When EXTPROC is set without ISTRIP or IUCLC, processing is identical to raw mode; handle this receiving mode as a special-case of raw mode. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Convert to modal receive_buf() processing; factor raw mode per-char i/o into n_tty_receive_buf_raw(). Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Prepare for modal receive_buf() handling; factor handling for TTY_BREAK, TTY_PARITY, TTY_FRAME and TTY_OVERRUN into n_tty_receive_char_flagged(). Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Reduce the monolithic n_tty_receive_char() complexity; factor the handling of INTR_CHAR, QUIT_CHAR and SUSP_CHAR into n_tty_receive_signal_char(). Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Convert to modal receive_buf() processing; factor real_raw receive_buf() into n_tty_receive_buf_real_raw(). Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Reduce pointer reloading and improve locality-of-reference; allocate read_buf and echo_buf within struct n_tty_data. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-