When multi queue compatable names are used by pktgen (eg eth0@0),
we currently cannot unload a NIC driver if one of its device
is currently in use.

Allow pktgen_find_dev() to find pktgen devices by their suffix (netdev name)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gso_max_size must be set based on the value of the underlying device to
support devices not using the full 64k.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The /dev/rfkill ops don't refer to the module,
so it is possible to unload the module while
file descriptors are open. Fix this oversight.
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Copied from original one-line patch here:

	http://bugzilla.kernel.org/show_bug.cgi?id=14267#c26Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix soft-lockup in hso.c which is triggered on SMP machine when
modem is removed while file descriptor(s) under /dev are still open:

  old version called kref_put() too early which resulted in destroying
  hso_serial and hso_device objects which were still used later on.
Signed-off-by: Antti Kaijanmäki <antti.kaijanmaki@nomovok.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Antti Kaijanmäki <antti.kaijanmaki@nomovok.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit e6fce5b9 (pktgen: multiqueue etc.) tried to relax
the pktgen restriction of one device per kernel thread, adding a '@'
tag to device names.

Problem is we dont perform check on full pktgen device name.
This allows adding many time same 'device' to pktgen thread

 pgset "add_device eth0@0"

one session later :

 pgset "add_device eth0@0"

(This doesnt find previous device)

This consumes ~1.5 MBytes of vmalloc memory per round and also triggers
this warning :

[  673.186380] proc_dir_entry 'pktgen/eth0@0' already registered
[  673.186383] Modules linked in: pktgen ixgbe ehci_hcd psmouse mdio mousedev evdev [last unloaded: pktgen]
[  673.186406] Pid: 6219, comm: bash Tainted: G        W  2.6.32-rc7-03302-g41cec6f1-dirty #16
[  673.186410] Call Trace:
[  673.186417]  [<ffffffff8104a29b>] warn_slowpath_common+0x7b/0xc0
[  673.186422]  [<ffffffff8104a341>] warn_slowpath_fmt+0x41/0x50
[  673.186426]  [<ffffffff8114e789>] proc_register+0x109/0x210
[  673.186433]  [<ffffffff8100bf2e>] ? apic_timer_interrupt+0xe/0x20
[  673.186438]  [<ffffffff8114e905>] proc_create_data+0x75/0xd0
[  673.186444]  [<ffffffffa006ad38>] pktgen_thread_write+0x568/0x640 [pktgen]
[  673.186449]  [<ffffffffa006a7d0>] ? pktgen_thread_write+0x0/0x640 [pktgen]
[  673.186453]  [<ffffffff81149144>] proc_reg_write+0x84/0xc0
[  673.186458]  [<ffffffff810f5a58>] vfs_write+0xb8/0x180
[  673.186463]  [<ffffffff810f5c11>] sys_write+0x51/0x90
[  673.186468]  [<ffffffff8100b51b>] system_call_fastpath+0x16/0x1b
[  673.186470] ---[ end trace ccbb991b0a8d994d ]---

Solution to this problem is to use a odevname field (includes @ tag and suffix),
instead of using netdevice name.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the external timer cannot be used the driver
will continue to work without mitigation.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit acc738fe (netfilter: xtables: avoid pointer to self) introduced
an invalid return value in limit_mt_check().
Signed-off-by: Patrick McHardy <kaber@trash.net>

Andreas Lohre reported that the driver crashes when trying
to register_netdev(), he sugessted to move dev->netdev_ops initialization
before calling register_netdev(), it worked for him.
Reported-by: Andreas Lohre <alohre@gmail.com>
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Along with netdev->perm_addr, mac address will be
  maintained in device private structure.

o Device limitation: We need to set mac address when ever
  interface comes up.

In ALB/TAL mode, bonding driver calls set_mac for all slave with bond mac address.
But bonding driver set netdev->dev_addr field to its original value,
after enslaving interfaces.

When ever active slave changes, it swap dev_addr of inactive slave with active.
Yet it doesn't notify driver about change in netdev->dev_addr.

As netxen driver need to set mac addr when ever interface comes up,
it can't rely on netdev->dev_addr field. Specially in case of bonding mode ALB/TLB.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kernel crashes, if promisc mode set without disabling rx queue.
Before changing mode in NX2031 chip, wait till rx queue drains.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid resetting memory during initialization, skip this memory
block during driver probe.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use BIT for macro definitions wherever possible, remove
unused and redundant macros.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Summary of Changes:

	-Fix to receive multicast packets by setting the corresponding hardware
	 bit during initialization.
	-Fix to re-enable the interface [by interface up command(ifup)] while the
	 interface is down.
	-Fix to be able to down the interface by passing the last parameter
	 correctly to request_irq().
	-Remove to read 4 extra bytes from the receiving queue after reading a
	 packet, even though it does not cause a predictable issue now.
	-Remove occurrences of transmission done interrupt in order to tx
	 throughput enhancement.
	-Enable IP checksum for packet receiving by setting the corresponding
	 hardware bit during initialization.
	-Relocate ks_enable_int()/ks_disable_int() in order not to declare those
	 functions at the beginning of the file.
	-Rename ks_enable()/_disable() to ks_enable_qmu()/ks_disable_qmu() in
	 order to give more meaningful names and relocate them not declaire
	 those functions at the beginning of the file.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When building for Sun 3:

drivers/net/ethoc.c:1091: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `ethoc_probe':
drivers/net/ethoc.c:965: undefined reference to `dma_alloc_coherent'
drivers/net/ethoc.c:1063: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When configuring the OEM bits in the PHY on 82577/82578, do not restart
autonegotiation if the firmware is blocking it (e.g. when an IDE-R session
is active) because the link must not go down.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A workaround for pre-release versions of 82577 is causing link issues on
some switches.  The workaround is no longer needed on production parts so
remove it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When changing MTU, save it off prior to resetting otherwise the flow control
thresholds may be miscalculated.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On some devices (e.g. 82578) not having a Tx timeout factor when linked at
100Mbps can cause false reports of hardware hangs on busy hubs.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When flow control (pause) parameters were changed via ethtool (i.e. enabled
or disabled), the newly calculated thresholds were not being written to the
device for non-fiber media.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove unnecessary workaround that mistakenly does not perform a page
select operation for PHY registers 29 and 30 (assuming these are the PHY
debug port address and data registers) on 82578 which can cause reads
of the Transmit with No Carrier Sense statistics register on page 778 to be
read from an incorrect page.  Also error out if the page select operation
fails.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 3ec2a2b8 broke Tx/Rx when using
jumbo frames on certain parts (i.e. only PAUSE frames could be exchanged
once the high water mark was reached preventing normal packet traffic).
This patch reverts the breakage and sets appropriate high and low water
marks of the Rx FIFO for 82577/82578 which require a workaround due to a
flow control issue in hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tc is required by CONFIG_IXGBE_DCB.
This also fixes compilation warning:

 drivers/net/ixgbe/ixgbe_main.c: In function ‘ixgbe_tx_is_paused’:
 drivers/net/ixgbe/ixgbe_main.c:245: warning: unused variable ‘tc’
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[  171.925285] BUG: sleeping function called from invalid context at kernel/mutex.c:280
[  171.925296] in_atomic(): 1, irqs_disabled(): 0, pid: 671, name: grep
[  171.925306] 2 locks held by grep/671:
[  171.925312]  #0:  (&p->lock){+.+.+.}, at: [<c10b8acd>] seq_read+0x25/0x36c
[  171.925340]  #1:  (rcu_read_lock){.+.+..}, at: [<c1391dac>] seq_start+0x0/0x44
[  171.925372] Pid: 671, comm: grep Not tainted 2.6.31.6-4-netbook #3
[  171.925380] Call Trace:
[  171.925398]  [<c105104e>] ? __debug_show_held_locks+0x1e/0x20
[  171.925414]  [<c10264ac>] __might_sleep+0xfb/0x102
[  171.925430]  [<c1461521>] mutex_lock_nested+0x1c/0x2ad
[  171.925444]  [<c1391c9e>] seq_show+0x74/0x127
[  171.925456]  [<c10b8c5c>] seq_read+0x1b4/0x36c
[  171.925469]  [<c10b8aa8>] ? seq_read+0x0/0x36c
[  171.925483]  [<c10d5c8e>] proc_reg_read+0x60/0x74
[  171.925496]  [<c10d5c2e>] ? proc_reg_read+0x0/0x74
[  171.925510]  [<c10a4468>] vfs_read+0x87/0x110
[  171.925523]  [<c10a458a>] sys_read+0x3b/0x60
[  171.925538]  [<c1002a49>] syscall_call+0x7/0xb

Fix it by replacing RCU with nf_log_mutex.
Reported-by: "Yin, Kangkai" <kangkai.yin@intel.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Return a negative error value.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

veth_get_stats() can be called in parallel on several cpus.

It's better to not reset dev->stats as it could give wrong result on
one cpu. Use temporary variables, then store the final results.

Also, we should loop on every possible cpus, not only online cpus,
or cpu hotplug can suddenly give wrong veth stats.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ieee802154_fake_xmit() should free skbs since it returns NETDEV_TX_OK
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When mac80211 resumes, it currently first sets suspended
to false so the driver can start doing things and we can
receive frames.

However, if we actually receive frames then it can end
up starting some work which adds timers and then later
runs into a BUG_ON in the timer code because it tries
add_timer() on a pending timer.

Fix this by keeping track of the resuming process by
introducing a new variable 'resuming' which gets set to
true early on instead of setting 'suspended' to false,
and allow queueing work but not receiving frames while
resuming.
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] Fix stale cpufreq_cpu_governor pointer
  [CPUFREQ] Resolve time unit thinko in ondemand/conservative govs
  [CPUFREQ] speedstep-ich: fix error caused by 394122ab
  [CPUFREQ] Fix use after free on governor restore
  [CPUFREQ] acpi-cpufreq: blacklist Intel 0f68: Fix HT detection and put in notification message
  [CPUFREQ] powernow-k8: Fix test in get_transition_latency()
  [CPUFREQ] longhaul: select Longhaul version 2 for capable CPUs

Doing the strcmp return value as

	signed char __res = *cs - *ct;

is wrong for two reasons.  The subtraction can overflow because __res
doesn't use a type big enough.  Moreover the compared bytes should be
interpreted as unsigned char as specified by POSIX.

The same problem is fixed in strncmp.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
  agp/intel-agp: Set dma_mask for capable chipsets before agp_add_bridge()

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  ima: replace GFP_KERNEL with GFP_NOFS

We should set this before calling agp_add_bridge() so that it's done
before we map the scratch page too.

This should probably fix the regression reported as k.o. bug #14627.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  OMAP: cs should be positive in gpmc_cs_free()
  omap: fix unlikely(x) < y
  omap3: clock: Fixed dpll3_m2x2 rate calculation
  omap3: clock: Fix the DPLL freqsel computations
  omap: Fix keymap for zoom2 according to matrix keypad framwork

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ASoC: tlv320aic23 fix rate selection
  ASoC: OMAP3 Pandora: update for TWL4030 codec changes
  ASoC: Modifying the license string GPLv2 for OMAP3 EVM
  ALSA: hda - Fix quirk for VAIO type G
  ALSA: usb - Quirk to disable master volume control in PCM2702

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
  cxgb3: fix premature page unmap
  ibm_newemac: Fix EMACx_TRTR[TRT] bit shifts
  vlan: Fix register_vlan_dev() error path
  gro: Fix illegal merging of trailer trash
  sungem: Fix Serdes detection.
  net: fix mdio section mismatch warning
  ppp: fix BUG on non-linear SKB (multilink receive)
  ixgbe: Fixing EEH handler to handle more than one error
  net: Fix the rollback test in dev_change_name()
  Revert "isdn: isdn_ppp: Use SKB list facilities instead of home-grown implementation."
  TI Davinci EMAC : Fix Console Hang when bringing the interface down
  smsc911x: Fix Console Hang when bringing the interface down.
  mISDN: fix error return in HFCmulti_init()
  forcedeth: mac address fix
  r6040: fix version printing
  Bluetooth: Fix regression with L2CAP configuration in Basic Mode
  Bluetooth: Select Basic Mode as default for SOCK_SEQPACKET
  Bluetooth: Set general bonding security for ACL by default
  r8169: Fix receive buffer length when MTU is between 1515 and 1536
  can: add the missing netlink get_xstats_size callback
  ...