- 21 Aug, 2017 3 commits
-
-
Simon Xue authored
Add H265e/VEPU/VPU/VDEC/VOP iommu nodes Signed-off-by: Simon Xue <xxm@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Romain Perier authored
This adds and enable the operating points that have been tested and are currently supported by the SoC. This also adds clocks for ARMCLKL and ARMCLKB. Signed-off-by: Romain Perier <romain.perier@collabora.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Joseph Chen authored
RK805 consists of 4 DCDCs, 3 LDOs. It's different from RK808 and RK818 that there are 2 output only GPIOs, we should add properties "gpio-controller" and "gpio-cells = <2>". Signed-off-by: Joseph Chen <chenjh@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
- 18 Aug, 2017 5 commits
-
-
Jeffy Chen authored
Currently we are assigning mic irq to rt5514 i2c driver, which is wrong. Assign it to rt5514 spi driver instead. Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Kever Yang authored
We need to init vop aclk and hclk incase the U-Boot does not do the initialize. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Mark Yao <mark.yao@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
David Wu authored
There are 4 pwm channels built in rk3328 soc, need to configure the both APB clock and bus clock. Signed-off-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Jeffy Chen authored
According to rt5514 dt-binding, it should be "realtek,dmic-init-delay-ms". Fixes: 48f4d979 (arm64: dts: rockchip: add Gru/Kevin DTS) Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
William Wu authored
RK3399 USB DWC3 controller has a issue that FS/LS devices not recognized if inserted through USB 3.0 HUB. It's because that the inter-packet delay between the SSPLIT token to SETUP token is about 566ns, more then the USB spec requirement. This patch adds a quirk "snps,dis-tx-ipgap-linecheck-quirk" to disable the u2mac linestate check to decrease the SSPLIT token to SETUP token inter-packet delay from 566ns to 466ns. Signed-off-by: William Wu <william.wu@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
- 13 Aug, 2017 1 commit
-
-
Heiko Stuebner authored
When adding the rk3399 sapphire som, two more of the recently removed num-slots properties of dw-mmc nodes slipped in. Remove them again. Fixes: 8164a84c ("arm64: dts: rockchip: Add support for rk3399 sapphire SOM") Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
- 11 Aug, 2017 3 commits
-
-
Rocky Hao authored
enable tsadc module on RK3328 eavluation board Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Rocky Hao authored
add thermal zone and dynamic CPU power coefficients for rk3328 Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Rocky Hao authored
add tsadc needed main information for rk3328 SoC. 50000Hz is the max clock rate supported by tsadc module. Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
- 07 Aug, 2017 1 commit
-
-
Sugar Zhang authored
This patch add the i2s dt nodes for rk3328. Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
- 06 Aug, 2017 9 commits
-
-
Jacob Chen authored
Add support for the rk3399 excavator main board. This board works in a combination with the sapphire SOM. This board have been sold as the rk3399 evaluation board for commercial customers. You can get more info from below link: http://opensource.rock-chips.com/wiki_Excavator_sapphire_boardSigned-off-by: Jacob Chen <jacob-chen@iotwrt.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Jacob Chen authored
Add support for the rk3399 sapphire SOM board. This board works in a combination with the excavator main board. You can get more info from below link: http://opensource.rock-chips.com/wiki_Excavator_sapphire_boardSigned-off-by: Jacob Chen <jacob-chen@iotwrt.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Jacob Chen authored
Add an hdmi node, and also add hdmi endpoints to vopb and vopl output port nodes. Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Jacob Chen authored
Add an mipi node, and also add mipi endpoints to vopb and vopl output port nodes. Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Yakir Yang authored
Add an edp node, and also add edp endpoints to vopb and vopl output port nodes. Signed-off-by: Yakir Yang <ykk@rock-chips.com> Signed-off-by: Caesar Wang <wxt@rock-chips.com> Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Elaine Zhang authored
1. add pd node for RK3399 Soc 2. create power domain tree 3. add qos node for domain Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com> Signed-off-by: Caesar Wang <wxt@rock-chips.com> Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Mark Yao authored
Add devicetree nodes for rk3399 VOP (Video Output Processors), and the top level display-subsystem root node. Later patches add endpoints (eDP, HDMI, MIPI, etc) that attach to the VOPs' output ports. Signed-off-by: Mark Yao <mark.yao@rock-chips.com> Signed-off-by: Yakir Yang <ykk@rock-chips.com> Signed-off-by: Caesar Wang <wxt@rock-chips.com> Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Jianqun Xu authored
Add opp tables for cpu cluster0 and cluster1 by including rk3399-opp.dtsi. Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Finley Xiao authored
This patch adds basic OPP entries for RK3328 SoC. Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
- 31 Jul, 2017 1 commit
-
-
Caesar Wang authored
This patch updates the dynamic-power-coefficient for big cluster on rk3399 SoCs. The dynamic power consumption of the CPU is proportional to the square of the Voltage (V) and the clock frequency (f). The coefficient is used to calculate the dynamic power as below - Pdyn = dynamic-power-coefficient * V^2 * f Where Voltage is in uV, frequency is in MHz. As the following is the tested data on rk3399's big cluster. frequency(MHz) Voltage(V) Current(mA) Dynamic-power-coefficient 24 0.8 15 48 0.8 23 ~417 96 0.8 40 ~443 216 0.8 82 ~438 312 0.8 115 ~430 408 0.8 150 ~455 So the dynamic-power-coefficient average value is about 436. Signed-off-by: Caesar Wang <wxt@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
- 29 Jul, 2017 2 commits
-
-
Sugar Zhang authored
This patch add the spdif dt node for rk3328. Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Sugar Zhang authored
This patch add the spdif dt node for rk3368 soc. Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
- 25 Jul, 2017 2 commits
-
-
Shawn Lin authored
This allows basic support for SD highspeed cards but no UHS-I mode got ready due to the propagated defer-probe error from RK805. Cc: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
David Wu authored
Add the core grf subnode for the io-domain controller. Signed-off-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
- 22 Jul, 2017 6 commits
-
-
Shawn Lin authored
Kill these two pinctrl reference totally from rk3399 as it never work indeed. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Shawn Lin authored
pcie_clkreqn actually doesn't work at all, so replace it with pcie_clkreqn_cpm. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Caesar Wang authored
This patch enables the gpu and adds the mali-supply power for RK3399-GRU devices. Signed-off-by: Caesar Wang <wxt@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Caesar Wang authored
Add Mali GPU device tree node for the RK3399 SoCs, with devfreq opp table. RK3399 and RK3399-OP1 SoCs have a different recommendation table with gpu opp. Also, the ARM's mali driver found on https://developer.arm.com/products/software/mali-drivers/midgard-kernel. Signed-off-by: Caesar Wang <wxt@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Caesar Wang authored
RK3399's GPU uses the quad-core Mali-T860, which is the new generation of high-end graphics processors from ARM. This patch added "rockchip,rk3399-mali" for dt-bindings, in order to support IPA of gpu thermal in later. Signed-off-by: Caesar Wang <wxt@rock-chips.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Shawn Lin authored
keep-power-in-suspend was invented for SDIO only, so it should not be used for eMMC node. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
- 16 Jul, 2017 7 commits
-
-
Shawn Lin authored
We deprecated the "num-slots" property now and plan to get rid of it finally. Just move a step to cleanup it from DT. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Shawn Lin authored
pcie_clkreqn actually doesn't work at all, so replace it with pcie_clkreqn_cpm. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Caesar Wang authored
The SdioAudio power domain includes the i2s/spdif/spi5/sdio. So this patch adds the pd control for rk3399 i2s/spdif/spi5/sdio, in order to save more power consumption. Signed-off-by: Caesar Wang <wxt@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
William Wu authored
Rockchip's RK3328 evaluation board has one usb2 otg controller and one usb2 host controller which consist of EHCI and OHCI. Each usb controller connects with one usb2 phy port through UTMI+ interface. Let's enable them to support usb2 on RK3328 evaluation board. Signed-off-by: William Wu <william.wu@rock-chips.com> [restructured enablement of u2phy subnodes] Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
William Wu authored
This patch adds usb2 otg/host controllers and phys nodes for Rockchip RK3328 SoCs. Signed-off-by: William Wu <william.wu@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Brian Norris authored
Provide the dynamic power coefficient of the big and little CPU clusters. These numbers are currently in use on the Samsung Chromebook Plus ("Kevin"). The power allocator thermal governor doesn't know how to do anything if it doesn't get power parameters from its cooling devices (in this case, CPUfreq). So this effectively enables the power-allocator governor. Signed-off-by: Brian Norris <briannorris@chromium.org> [set the property in each core node] Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-
Matthias Kaehlcke authored
The Gru device tree currently contains entries for the regulators ppvar_bigcpu, ppvar_litcpu, ppvar_gpu and ppvar_centerlogic; however, the regulators have not been enabled, due to the lack of binding and driver support for keeping the over-voltage protection (OVP) at bay and preventing unintended regulator shutdowns on voltage downshifts. Now, the vctrl regulator driver has been merged, along with new bindings for asymmetric settling time. The driver is OVP aware, it splits larger voltage decreases in multiple steps when necessary and adds required delays. This change renames each of the aforementioned regulators to <orig_name>_pwm and adds a new vctrl regulator named <orig_name>. The vctrl regulators use the voltage of their corresponding PWM regulator as control voltage. The OVP related values are empirical and stem from the Chrome OS kernel tree. Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Brian Norris <briannorris@chromium.org> [fixed node names and parent supplies of gpu and centerlogic] Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-