Add support for ZII's i.MX7 based Remote Peripheral Unit 2 (RPU2)
board.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Rob Herring <robh@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Running reboot command on the TQMa7 board would just hang infinite
at the end of the system shutdown process.

Handling of i.MX7 errata e10574:
Watchdog: A watchdog timeout or software trigger will not reset the SOC.

Moved pinctrl from common mba7 to common tqma7 dtsi as it improves
readability of errata handling. Most integrators of this SoM will
likely use the development board as inspiration for handling this
SoC issue.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add device tree for the Menlosystems board based on i.MX53 M53 SoM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Rename the touchscreen node to match contemporary design.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Update i.MX6DL automotive part's opp table according to i.MX6DL
automotive datasheet Rev.9, 11/2018, it adds 996MHz set-point
support as below:

LDO enabled(min value):
996MHz: VDDARM: 1.275V, VDDSOC: 1.175V;
792MHz: VDDARM: 1.150V, VDDSOC: 1.150V;
396MHz: VDDARM: 1.125V, VDDSOC: 1.150V;

Adding 25mV to cover board IR drop, for LDO enabled mode of 996MHz,
as the max value of LDO output can NOT exceed 1.3V, so 25mV is NOT
added for VDDARM.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The devicetree specification recommends using generic node names.

Some Zii dts files already follow such recommendation, but some don't,
so use generic node names for consistency among the Zii dts files.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The LCD power sequencer is very finicky.  The backlight cannot
be driven until after the sequencer is done.  Until now, the
regulators were marked with 'regulator-always-on' to make sure
it came up before the backlight.  This patch allows the LCD
regulators to power down and prevent the backlight from being
used again until the sequencer is ready.  This reduces
standby power consumption by ~100mW.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The original submission had functional audio out and was based
on reviewing other boards using the same wm8962 codec. However,
the Logic PD board uses an analog microphone which was being
disabled for a digital mic.  This patch corrects that and
explicitly sets the gpio-cfg pins all to 0x0000 which allows the
analog microphone to capture audio.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add #cooling-cells for i.MX6SLL cpu-freq cooling device usage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Kobo Aura is an e-book reader released in 2013.

With the devicetree in its current state, the kernel will boot and run
for about ten seconds. To solve this, the embedded controller needs to
be told that the system should stay powered on. This will be done in a
later patchset.

- The IOMUXC mode bits for the SD interfaces were taken from the
  vendor's U-Boot fork.
- The bus width of the eMMC is 4 bits in the vendor kernel, but I
  achieved better performance with 8 bits.
- The SDIO clock frequency for the WiFi chip is 25MHz in the vendor
  kernel, but the WiFi chip (BCM43362) supports 50MHz, which works
  reliably on this board and gives slightly better performance.
- The I2C pins' IOMUXC settings come from the vendor's U-Boot fork.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The correct DT property for specifying a GPIO used for reset
is "reset-gpios", the driver now accepts this name, use it here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The correct DT property for specifying a GPIO used for reset
is "reset-gpios", the driver now accepts this name, use it here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The correct DT property for specifying a GPIO used for reset
is "reset-gpios", the driver now accepts this name, use it here.

Note the GPIO polarity in the driver was ignored before and always
assumed to be active low, when all the DTs are fixed we will start
respecting the specified polarity. Switch polarity in DT to the
currently assumed one, this way when the driver changes the
behavior will not change.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since 25aaa75d SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since 25aaa75d SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since 25aaa75d SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since 25aaa75d SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SL_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since 25aaa75d SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SLL_CLK_SDMA result in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SLL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since 25aaa75d SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6UL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6UL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since 25aaa75d SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX7D_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX7D_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since 25aaa75d SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SX_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SX_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since 25aaa75d SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6QDL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality(this at least
breaks RAVE SP serdev driver on RDU2). Fix the code to specify
IMX6QDL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting incorrect
clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Warp7 comes with a Omnivision OV2680 sensor, add the node here to make
complete the camera data path for this system. Add the needed regulator
to the analog voltage supply, the port and endpoints in mipi_csi node
and the pinctrl for the reset gpio.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add and enable csi and mipi_csi nodes.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add device tree nodes for csi, video multiplexer and mipi-csi.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The IOMUXC General Purpose Register has bitfield to control video bus
multiplexer to control the CSI input between the MIPI-CSI2 and parallel
interface. Add that register and mask.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add power domain index 0 related with mipi-phy to imx7s.

While at it rename pcie power-domain node to remove pgc prefix.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds support for the TQ TQMa7D SoM together with
the MBa7 carrier board and it's based on the NXP i.MX7Dual SoC.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds support for the TQ TQMa7S SoM together with
the MBa7 carrier board and it's based on the NXP i.MX7Solo SoC.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds TQMa7 and MBa7 board support.
TQMa7 can be mounted with either i.MX7 Solo or Dual.
All TQMa7 board variants can be mounted in MBa7 carrier board.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX6 comes with 4 viewports, so configure PCIE node accordingly so
that the driver won't assume we only have 2.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX7D comes with 4 viewports, so configure PCIE node accordingly so
that the driver won't assume we only have 2.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Only a certain number of CFU1's come with NOR flash populated. Disable
it by default to avoid trying to probe NOR flash on devices that don't
have it. Devices that do have it can rely on the bootloader to enable
this node.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add Device Tree for VF610 based Zodiac Seat Power Box.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX7ULP OCOTP support, its clock source is from
M4 BUS clock which is NOT available in Linux clock tree,
but M4 BUS clock is always ON when A7 (Linux) is alive,
so just use dummy clock here.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This is one of two boards that make use of the recently introduced SIOX
bus. Apart from the devices described in the dts it features a display
with touch that I didn't include here because it needs some non-mainline
change to operate correctly.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

After switching to the new FSL QSPI driver the properties
'fsl,qspi-has-second-chip' and 'big-endian' are not used anymore.

The driver now uses the 'reg' property to determine the bus and
the chipselect. The endianness is selected by the driver depending
on which SoC is used.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Even though the ChipIdea USB controller binding[1] doesn't specify the
properties that reference a PHY as required, the Linux driver
requires[2] such a reference.

The clock situation is like on i.MX53: The USB controller is clocked
from IMX5_CLK_USBOH3_GATE and the PHY from IMX5_CLK_USB_PHY1_GATE.

[1]: Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
[2]: Search for EINVAL in drivers/usb/chipidea/ci_hdrc_imx.c
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Using aliases, the devices will be enumerated properly.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>