The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

am335x-evm has only one CPSW external port physically wired, but DT defines
2 ext. ports. As result, PHY connection failure reported for the second
ext. port.

Update DT to reflect am335x-evm board HW configuration, and, while here,
switch to use phy-handle instead of phy_id.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The SN65HVS882 load trigger is attached to GPIO2_23 on the AM571x IDK.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

AM572x-IDK rev 1.3A has tricolor RGB LEDs that can be controlled using
GPIO. Expose these to userspace for usage as necessary.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

AM571x-IDK rev 1.2A has tricolor RGB LEDs that can be controlled using
GPIO. Expose these to userspace for usage as necessary.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GTA04A5 has been produced with MCP chips either with
 512MB RAM +  512MB NAND
 512MB RAM + 1024MB NAND
1024MB RAM +  512MB OneNAND

RAM setup is done by U-Boot (MLO/SPL) but OneNAND needs
a different setup of the GPMC. So we need to derive a
DTB variant that modifies the gpmc and nand setup.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Properly pinmux the bluetooth enable so that it is not floating.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Sensors for acceleration, rotation, magnetic heading and
barometer have been replaced in the A5 variant.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GTA04A5 uses a ti,wl1837 WiFi/Bluetooth module. Overwrite
the mmc2 node and child.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The GTA04A5 has an improved IrDA circuit that can enable/disable
the receiver individually. We do not have an IrDA driver/subsystem
and hence the receiver should be actively turned off to save power,
especially in suspend.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GPS receiver provides a 1PPS signal to a gpio.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

in node sound / property ti,jack-det-gpio.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GTA04 is the project name and Letux 2804 the product name.
Report both.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GTA04 is the project name and Letux 2804 the product name.
Report both.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GTA04 is the project name and Letux 2804 the product name.
Report both.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GTA04 audio system makes use of all four McBSP ports, so enable and
connect them with pinmux.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

McBSP1 needs special "pinctrl" for the clocks.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GTA04 audio system makes use of all four McBSP ports, so set
up proper pinmux.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ISP needs camera pinmux (which is referenced by the camera node).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The GTA04 has an optional OV9655 camera (for which we do
not yet have a driver upstream), but the ISP hardware
connection description in the device tree is independent
of that.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GTA04 can detect presence/absence or plug-in of an external
GPS antenna through a gpio. The best match for an event code
is SW_LINEIN_INSERT.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

we can replace magic numbers by symbolic constants now.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

There are neither CD nor WP switches for mmc1. The µSD slot is
located under the SIM card under the battery and not accessible
during operation.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

vaux2 should remain always on since a higher potential at vio
could potentially damage the itg3200 sensor.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Make clear how to use the wifi_reset since it is not obvious.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This is needed to make the display and venc work properly.
Compare to omap3-beagle.dts.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

to better match omap3-beagle.dts (which was the basis
of designing the GTA04).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Vendor defined U-Boot has changed the partition scheme a while ago:

* kernel partition 6MB
* file system partition uses the remainder up to end of the NAND
* increased size of the environment partition (to get an OneNAND compatible base address)
* shrink the U-Boot partition

Let's be compatible (e.g. Debian kernel built from upstream).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

we fix penirq polarity, add penirq pinmux and touchscreen
properties.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The omap dss susbystem takes the display aliases to find
out which displays exist. To enable tv-out we must define
an alias.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The VENC with external OPA362 amplifier needs a special
"pinmux" setup in DEVCONF1 (TVOUTBYPASS and TVOUTACEN).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

* fix connector compatibility (composite)
* add comment for gpio1 23
* add proper #address-cells
* we use only one venc_out channel for composite
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

needed for device variants based on GTA04 board but with
different display panel (driver).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

tab+space -> tab only	 for /* GSM audio */
spaces -> tab for dss_dpi_pins
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

mn -> nm for backlight_pins
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>