Daniel Borkmann says:

====================
pull-request: bpf 2018-01-18

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix a divide by zero due to wrong if (src_reg == 0) check in
   64-bit mode. Properly handle this in interpreter and mask it
   also generically in verifier to guard against similar checks
   in JITs, from Eric and Alexei.

2) Fix a bug in arm64 JIT when tail calls are involved and progs
   have different stack sizes, from Daniel.

3) Reject stores into BPF context that are not expected BPF_STX |
   BPF_MEM variant, from Daniel.

4) Mark dst reg as unknown on {s,u}bounds adjustments when the
   src reg has derived bounds from dead branches, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't change endianness when assigning vlan value in cxgb4_tc_flower
code when processing flow match parameters. The value gets converted
to network order as part of filtering code in set_filter_wr.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For ethtype_key = ETH_P_IPV6, set filter type as 1 in cxgb4_tc_flower
code when processing flow match parameters.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Helmut reported a bug about division by zero while
running traffic and doing physical cable pull test.

When the cable unplugged the ppms become zero, so when
dividing the current ppms by the previous ppms in the
next dim iteration there is division by zero.

This patch prevent this division for both ppms and epms.

Fixes: c3164d2f ("net/mlx5e: Added BW check for DIM decision mechanism")
Reported-by: Helmut Grauer <helmut.grauer@de.ibm.com>
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull tracing fixes from Steven Rostedt:
 "Two more small fixes

   - The conversion of enums into their actual numbers to display in the
     event format file had an off-by-one bug, that could cause an enum
     not to be converted, and break user space parsing tools.

   - A fix to a previous fix to bring back the context recursion checks.
     The interrupt case checks for NMI, IRQ and softirq, but the softirq
     returned the same number regardless if it was set or not, although
     the logic would force it to be set if it were hit"

* tag 'trace-v4.15-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Fix converting enum's from the map in trace_event_eval_update()
  ring-buffer: Fix duplicate results in mapping context to bits in recursive lock

Pull input fixes from Dmitry Torokhov:

 - a fix for use-after-free in Synaptics RMI4 driver

 - correction to multitouch contact tracking on certain ALPS touchpads
   (which got broken when we tried to fix the 2-finger scrolling)

 - touchpad on Lenovo T640p is switched over to SMbus/RMI

 - a few device node refcount fixes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics-rmi4 - prevent UAF reported by KASAN
  Input: ALPS - fix multi-touch decoding on SS4 plus touchpads
  Input: synaptics - Lenovo Thinkpad T460p devices should use RMI
  Input: of_touchscreen - add MODULE_LICENSE
  Input: 88pm860x-ts - fix child-node lookup
  Input: twl6040-vibra - fix child-node lookup
  Input: twl4030-vibra - fix sibling-node lookup

Pull i2c fixes from Wolfram Sang:
 "Two bugfixes for the I2C core: Lixing Wang fixed a refcounting problem
  with DT nodes. Jeremy Compostella fixed a buffer overflow possibility
  when using a 'don't use' ioctl interface directly"

* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: core-smbus: prevent stack corruption on read I2C_BLOCK_DATA
  i2c: core: decrease reference count of device node in i2c_unregister_device

Pull libata fixlet from Tejun Heo:
 "This just adds one more entry for liteon optical drives to the device
  blacklist for large IOs.

  The change is very low risk"

* 'for-4.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  libata: apply MAX_SEC_1024 to all LITEON EP1 series devices

Pull cgroup fix from Tejun Heo:
 "cgroup.threads should be delegatable (ie. a container should be able
  to write to it from inside) but was missing the flag.

  The change is very low risk"

* 'for-4.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: make cgroup.threads delegatable

Pull workqueue fixlet from Tejun Heo:
 "One patch to add touch_nmi_watchdog() while dumping workqueue debug
  messages to avoid triggering the lockup detector spuriously.

  The change is very low risk"

* 'for-4.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: avoid hard lockups in show_workqueue_state()

Pull ARM SoC fixes from Arnd Bergmann:
 "We have various small DT fixes, and one important regression fix:

  The recent device tree bugfixes that were intended to address issues
  that 'dtc' started warning about in 4.15 fixed various USB PHY device
  nodes, but it turns out that we had code that depended on those nodes
  being incorrect and the probe failing with a particular error code.
  With the workaround we can also deal with correct device nodes.

  The DT fixes include:

   - Allwinner A10 and A20 had the display pipeline set up incorrectly
     (introduced in v4.15)

   - The Altera PMU lacked an interrupt-parent (never worked)

   - Pin muxing on the Openblocks A7 (never worked)

   - Clocks might get set up wrong on Armada 7K/8K (4.15 regression)

  We now have additional device tree patches to address all the
  remaining warnings introduced in 4.15, but decided to queue them for
  4.16 instead, to avoid risking another regression like the USB PHY
  thing mentioned above.

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  phy: work around 'phys' references to usb-nop-xceiv devices
  ARM: sunxi_defconfig: Enable CMA
  arm64: dts: socfpga: add missing interrupt-parent
  ARM: dts: sun[47]i: Fix display backend 1 output to TCON0 remote endpoint
  ARM64: dts: marvell: armada-cp110: Fix clock resources for various node
  ARM: dts: da850-lcdk: Remove leading 0x and 0s from unit address
  ARM: dts: kirkwood: fix pin-muxing of MPP7 on OpenBlocks A7

Pull powerpc fixes from Michael Ellerman:
 "More than we'd like after rc8, but nothing very alarming either, just
  tying up loose ends before the release:

  Since we changed powernv to use cpufreq_get() from show_cpuinfo(), we
  see warnings with PREEMPT enabled. But the preempt_disable() in
  show_cpuinfo() doesn't actually prevent CPU hotplug as it suggests, so
  remove it.

  Two updates to the recently merged RFI flush code. Wire up the generic
  sysfs file to report the status, and add a debugfs file to allow
  enabling/disabling it at runtime.

  Two updates to xmon, one to add the RFI flush related fields to the
  paca dump, and another to not use hashed pointers in the paca dump.

  And one minor fix to add a missing include of linux/types.h in
  asm/hvcall.h, not seen to break the build in upstream, but correct
  anyway.

  Thanks to: Benjamin Herrenschmidt, Michal Suchanek, Nicholas Piggin"

* tag 'powerpc-4.15-8' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/pseries: include linux/types.h in asm/hvcall.h
  powerpc/64s: Allow control of RFI flush via debugfs
  powerpc/64s: Wire up cpu_show_meltdown()
  powerpc: Don't preempt_disable() in show_cpuinfo()
  powerpc/xmon: Don't print hashed pointers in paca dump
  powerpc/xmon: Add RFI flush related fields to paca dump

Pull drm fixes from Dave Airlie:
 "Nouveau, i915, vmwgfx and sun4i regression fixes.

  The i915 change fixes a display corruption problem introduced in 4.15,
  the nouveau changes are for regressions in 4.15, one of the vmwgfx
  fixes goes back a little further, the other is a 4.15 regression fix,
  the 3 sun4i changes fix blank HDMI output on those devices"

* tag 'drm-fixes-for-v4.15-rc9' of git://people.freedesktop.org/~airlied/linux:
  drm/nouveau/mmu/mcp77: fix regressions in stolen memory handling
  drm/nouveau/bar/gk20a: Avoid bar teardown during init
  drm/nouveau/drm/nouveau: Pass the proper arguments to nvif_object_map_handle()
  drm/vmwgfx: fix memory corruption with legacy/sou connectors
  drm/vmwgfx: Fix a boot time warning
  drm/i915: Fix deadlock in i830_disable_pipe()
  drm/i915: Redo plane sanitation during readout
  drm/i915: Add .get_hw_state() method for planes
  drm/sun4i: hdmi: Add missing rate halving check in sun4i_tmds_determine_rate
  drm/sun4i: hdmi: Fix incorrect assignment in sun4i_tmds_determine_rate
  drm/sun4i: hdmi: Check for unset best_parent in sun4i_tmds_determine_rate

Merge misc fixes from Andrew Morton:
 "6 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  sparse doesn't support struct randomization
  proc: fix coredump vs read /proc/*/stat race
  scripts/gdb/linux/tasks.py: fix get_thread_info
  scripts/decodecode: fix decoding for AArch64 (arm64) instructions
  mm/page_owner.c: remove drain_all_pages from init_early_allocated_pages
  mm/memory.c: release locked page in do_swap_page()

Force __builtin_constant_p to evaluate whether the argument to atomic_add
& atomic_sub is constant in the front-end before optimisations which
can lead GCC to output a call to __bad_increment_for_ia64_fetch_and_add().

See GCC bugzilla 83653.
Signed-off-by: Jakub Jelinek <jakub@redhat.com>
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Without this patch, I drown in a sea of unknown attribute warnings

Link: http://lkml.kernel.org/r/20180117024539.27354-1-willy@infradead.orgSigned-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

do_task_stat() accesses IP and SP of a task without bumping reference
count of a stack (which became an entity with independent lifetime at
some point).

Steps to reproduce:

    #include <stdio.h>
    #include <sys/types.h>
    #include <sys/stat.h>
    #include <fcntl.h>
    #include <sys/time.h>
    #include <sys/resource.h>
    #include <unistd.h>
    #include <sys/wait.h>

    int main(void)
    {
    	setrlimit(RLIMIT_CORE, &(struct rlimit){});

    	while (1) {
    		char buf[64];
    		char buf2[4096];
    		pid_t pid;
    		int fd;

    		pid = fork();
    		if (pid == 0) {
    			*(volatile int *)0 = 0;
    		}

    		snprintf(buf, sizeof(buf), "/proc/%u/stat", pid);
    		fd = open(buf, O_RDONLY);
    		read(fd, buf2, sizeof(buf2));
    		close(fd);

    		waitpid(pid, NULL, 0);
    	}
    	return 0;
    }

    BUG: unable to handle kernel paging request at 0000000000003fd8
    IP: do_task_stat+0x8b4/0xaf0
    PGD 800000003d73e067 P4D 800000003d73e067 PUD 3d558067 PMD 0
    Oops: 0000 [#1] PREEMPT SMP PTI
    CPU: 0 PID: 1417 Comm: a.out Not tainted 4.15.0-rc8-dirty #2
    Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc27 04/01/2014
    RIP: 0010:do_task_stat+0x8b4/0xaf0
    Call Trace:
     proc_single_show+0x43/0x70
     seq_read+0xe6/0x3b0
     __vfs_read+0x1e/0x120
     vfs_read+0x84/0x110
     SyS_read+0x3d/0xa0
     entry_SYSCALL_64_fastpath+0x13/0x6c
    RIP: 0033:0x7f4d7928cba0
    RSP: 002b:00007ffddb245158 EFLAGS: 00000246
    Code: 03 b7 a0 01 00 00 4c 8b 4c 24 70 4c 8b 44 24 78 4c 89 74 24 18 e9 91 f9 ff ff f6 45 4d 02 0f 84 fd f7 ff ff 48 8b 45 40 48 89 ef <48> 8b 80 d8 3f 00 00 48 89 44 24 20 e8 9b 97 eb ff 48 89 44 24
    RIP: do_task_stat+0x8b4/0xaf0 RSP: ffffc90000607cc8
    CR2: 0000000000003fd8

John Ogness said: for my tests I added an else case to verify that the
race is hit and correctly mitigated.

Link: http://lkml.kernel.org/r/20180116175054.GA11513@avx2Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reported-by: "Kohli, Gaurav" <gkohli@codeaurora.org>
Tested-by: John Ogness <john.ogness@linutronix.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since kernel 4.9, the thread_info has been moved into task_struct, no
longer locates at the bottom of kernel stack.

See commits c65eacbe ("sched/core: Allow putting thread_info into
task_struct") and 15f4eae7 ("x86: Move thread_info into
task_struct").

Before fix:
  (gdb) set $current = $lx_current()
  (gdb) p $lx_thread_info($current)
  $1 = {flags = 1470918301}
  (gdb) p $current.thread_info
  $2 = {flags = 2147483648}

After fix:
  (gdb) p $lx_thread_info($current)
  $1 = {flags = 2147483648}
  (gdb) p $current.thread_info
  $2 = {flags = 2147483648}

Link: http://lkml.kernel.org/r/20180118210159.17223-1-imxikangjie@gmail.com
Fixes: 15f4eae7 ("x86: Move thread_info into task_struct")
Signed-off-by: Xi Kangjie <imxikangjie@gmail.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Kieran Bingham <kbingham@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There are a couple of problems with the decodecode script and arm64:

1. AArch64 objdump refuses to disassemble .4byte directives as instructions,
   insisting that they are data values and displaying them as:

	a94153f3	.word	0xa94153f3		<-- trapping instruction

   This is resolved by using the .inst directive instead.

2. Disassembly of branch instructions attempts to provide the target as
   an offset from a symbol, e.g.:

   0:	34000082	cbz	w2, 10 <.text+0x10>

  however this falls foul of the grep -v, which matches lines containing
  ".text" and ends up removing all branch instructions from the dump.

This patch resolves both issues by using the .inst directive for 4-byte
quantities on arm64 and stripping the resulting binaries (as is done on
arm already) to remove the mapping symbols.

Link: http://lkml.kernel.org/r/1506596147-23630-1-git-send-email-will.deacon@arm.comSigned-off-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When setting page_owner = on, the following warning can be seen in the
boot log:

  WARNING: CPU: 0 PID: 0 at mm/page_alloc.c:2537 drain_all_pages+0x171/0x1a0
  Modules linked in:
  CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.15.0-rc7-next-20180109-1-default+ #7
  Hardware name: Dell Inc. Latitude E7470/0T6HHJ, BIOS 1.11.3 11/09/2016
  RIP: 0010:drain_all_pages+0x171/0x1a0
  Call Trace:
    init_page_owner+0x4e/0x260
    start_kernel+0x3e6/0x4a6
    ? set_init_arg+0x55/0x55
    secondary_startup_64+0xa5/0xb0
  Code: c5 ed ff 89 df 48 c7 c6 20 3b 71 82 e8 f9 4b 52 00 3b 05 d7 0b f8 00 89 c3 72 d5 5b 5d 41 5

This warning is shown because we are calling drain_all_pages() in
init_early_allocated_pages(), but mm_percpu_wq is not up yet, it is being
set up later on in kernel_init_freeable() -> init_mm_internals().

Link: http://lkml.kernel.org/r/20180109153921.GA13070@techadventures.netSigned-off-by: Oscar Salvador <osalvador@techadventures.net>
Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Ayush Mittal <ayush.m@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

James reported a bug in swap paging-in from his testing.  It is that
do_swap_page doesn't release locked page so system hang-up happens due
to a deadlock on PG_locked.

It was introduced by 0bcac06f ("mm, swap: skip swapcache for swapin
of synchronous device") because I missed swap cache hit places to update
swapcache variable to work well with other logics against swapcache in
do_swap_page.

This patch fixes it.

Debugged by James Bottomley.

Link: http://lkml.kernel.org/r/<1514407817.4169.4.camel@HansenPartnership.com>
Link: http://lkml.kernel.org/r/20180102235606.GA19438@bboxSigned-off-by: Minchan Kim <minchan@kernel.org>
Reported-by: James Bottomley <James.Bottomley@hansenpartnership.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:

 1) Fix BPF divides by zero, from Eric Dumazet and Alexei Starovoitov.

 2) Reject stores into bpf context via st and xadd, from Daniel
    Borkmann.

 3) Fix a memory leak in TUN, from Cong Wang.

 4) Disable RX aggregation on a specific troublesome configuration of
    r8152 in a Dell TB16b dock.

 5) Fix sw_ctx leak in tls, from Sabrina Dubroca.

 6) Fix program replacement in cls_bpf, from Daniel Borkmann.

 7) Fix uninitialized station_info structures in cfg80211, from Johannes
    Berg.

 8) Fix miscalculation of transport header offset field in flow
    dissector, from Eric Dumazet.

 9) Fix LPM tree leak on failure in mlxsw driver, from Ido Schimmel.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
  ibmvnic: Fix IPv6 packet descriptors
  ibmvnic: Fix IP offload control buffer
  ipv6: don't let tb6_root node share routes with other node
  ip6_gre: init dev->mtu and dev->hard_header_len correctly
  mlxsw: spectrum_router: Free LPM tree upon failure
  flow_dissector: properly cap thoff field
  fm10k: mark PM functions as __maybe_unused
  cfg80211: fix station info handling bugs
  netlink: reset extack earlier in netlink_rcv_skb
  can: af_can: canfd_rcv(): replace WARN_ONCE by pr_warn_once
  can: af_can: can_rcv(): replace WARN_ONCE by pr_warn_once
  bpf: mark dst unknown on inconsistent {s, u}bounds adjustments
  bpf: fix cls_bpf on filter replace
  Net: ethernet: ti: netcp: Fix inbound ping crash if MTU size is greater than 1500
  tls: reset crypto_info when do_tls_setsockopt_tx fails
  tls: return -EBUSY if crypto_info is already set
  tls: fix sw_ctx leak
  net/tls: Only attach to sockets in ESTABLISHED state
  net: fs_enet: do not call phy_stop() in interrupts
  r8152: disable RX aggregation on Dell TB16 dock
  ...

Stefan Wahren reports a problem with a warning fix that was merged
for v4.15: we had lots of device nodes with a 'phys' property pointing
to a device node that is not compliant with the binding documented in
Documentation/devicetree/bindings/phy/phy-bindings.txt

This generally works because USB HCD drivers that support both the generic
phy subsystem and the older usb-phy subsystem ignore most errors from
phy_get() and related calls and then use the usb-phy driver instead.

However, it turns out that making the usb-nop-xceiv device compatible with
the generic-phy binding changes the phy_get() return code from -EINVAL to
-EPROBE_DEFER, and the dwc2 usb controller driver for bcm2835 now returns
-EPROBE_DEFER from its probe function rather than ignoring the failure,
breaking all USB support on raspberry-pi when CONFIG_GENERIC_PHY is
enabled. The same code is used in the dwc3 driver and the usb_add_hcd()
function, so a reasonable assumption would be that many other platforms
are affected as well.

I have reviewed all the related patches and concluded that "usb-nop-xceiv"
is the only USB phy that is affected by the change, and since it is by far
the most commonly referenced phy, all the other USB phy drivers appear
to be used in ways that are are either safe in DT (they don't use the
'phys' property), or in the driver (they already ignore -EPROBE_DEFER
from generic-phy when usb-phy is available).

To work around the problem, this adds a special case to _of_phy_get()
so we ignore any PHY node that is compatible with "usb-nop-xceiv",
as we know that this can never load no matter how much we defer. In the
future, we might implement a generic-phy driver for "usb-nop-xceiv"
and then remove this workaround.

Since we generally want older kernels to also want to work with the
fixed devicetree files, it would be good to backport the patch into
stable kernels as well (3.13+ are possibly affected), even though they
don't contain any of the patches that may have caused regressions.

Fixes: 014d6da6 ARM: dts: bcm283x: Fix DTC warnings about missing phy-cells
Fixes: c5bbf358 arm: dts: nspire: Add missing #phy-cells to usb-nop-xceiv
Fixes: 44e5dced arm: dts: marvell: Add missing #phy-cells to usb-nop-xceiv
Fixes: f568f6f5 ARM: dts: omap: Add missing #phy-cells to usb-nop-xceiv
Fixes: d745d5f2 ARM: dts: imx51-zii-rdu1: Add missing #phy-cells to usb-nop-xceiv
Fixes: 915fbe59 ARM: dts: imx: Add missing #phy-cells to usb-nop-xceiv
Link: https://marc.info/?l=linux-usb&m=151518314314753&w=2
Link: https://patchwork.kernel.org/patch/10158145/
Cc: stable@vger.kernel.org
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The DRM driver most notably, but also out of tree drivers (for now) like
the VPU or GPU drivers, are quite big consumers of large, contiguous memory
buffers. However, the sunxi_defconfig doesn't enable CMA in order to
mitigate that, which makes them almost unusable.

Enable it to make sure it somewhat works.

Cc: <stable@vger.kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'drm-intel-fixes-2018-01-18' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

Display corruption regression bugfix with both a prep patch and a
follow-up fix

* tag 'drm-intel-fixes-2018-01-18' of git://anongit.freedesktop.org/drm/drm-intel:
  drm/i915: Fix deadlock in i830_disable_pipe()
  drm/i915: Redo plane sanitation during readout
  drm/i915: Add .get_hw_state() method for planes

Packet descriptor generation for IPv6 is broken.
Properly set L3 and L4 protocol flags for IPv6 descriptors.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set some missing fields in the IP control offload buffer. This buffer is
used to enable checksum and TCP segmentation offload in the VNIC server.
The buffer length field and the checksum offloading bits were not set
properly, so fix that here.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.15-20180118' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2018-01-18

====================
this is a pull reqeust of two patches for net/master:

The syzkaller project triggered two WARN_ONCE() in the af_can code from
userspace and we decided to replace it by a pr_warn_once().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 4512c43e, if we add a route to the subtree of tb6_root
which does not have any route attached to it yet, the current code will
let tb6_root and the node in the subtree share the same route.
This could cause problem cause tb6_root has RTN_INFO flag marked and the
tree repair and clean up code will not work properly.
This commit makes sure tb6_root->leaf points back to null_entry instead
of sharing route with other node.

It fixes the following syzkaller reported issue:
BUG: KASAN: use-after-free in ipv6_prefix_equal include/net/ipv6.h:540 [inline]
BUG: KASAN: use-after-free in fib6_add_1+0x165f/0x1790 net/ipv6/ip6_fib.c:618
Read of size 8 at addr ffff8801bc043498 by task syz-executor5/19819

CPU: 1 PID: 19819 Comm: syz-executor5 Not tainted 4.15.0-rc7+ #186
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:17 [inline]
 dump_stack+0x194/0x257 lib/dump_stack.c:53
 print_address_description+0x73/0x250 mm/kasan/report.c:252
 kasan_report_error mm/kasan/report.c:351 [inline]
 kasan_report+0x25b/0x340 mm/kasan/report.c:409
 __asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:430
 ipv6_prefix_equal include/net/ipv6.h:540 [inline]
 fib6_add_1+0x165f/0x1790 net/ipv6/ip6_fib.c:618
 fib6_add+0x5fa/0x1540 net/ipv6/ip6_fib.c:1214
 __ip6_ins_rt+0x6c/0x90 net/ipv6/route.c:1003
 ip6_route_add+0x141/0x190 net/ipv6/route.c:2790
 ipv6_route_ioctl+0x4db/0x6b0 net/ipv6/route.c:3299
 inet6_ioctl+0xef/0x1e0 net/ipv6/af_inet6.c:520
 sock_do_ioctl+0x65/0xb0 net/socket.c:958
 sock_ioctl+0x2c2/0x440 net/socket.c:1055
 vfs_ioctl fs/ioctl.c:46 [inline]
 do_vfs_ioctl+0x1b1/0x1520 fs/ioctl.c:686
 SYSC_ioctl fs/ioctl.c:701 [inline]
 SyS_ioctl+0x8f/0xc0 fs/ioctl.c:692
 entry_SYSCALL_64_fastpath+0x23/0x9a
RIP: 0033:0x452ac9
RSP: 002b:00007fd42b321c58 EFLAGS: 00000212 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 000000000071bea0 RCX: 0000000000452ac9
RDX: 0000000020fd7000 RSI: 000000000000890b RDI: 0000000000000013
RBP: 000000000000049e R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000212 R12: 00000000006f4f70
R13: 00000000ffffffff R14: 00007fd42b3226d4 R15: 0000000000000000

Fixes: 4512c43e ("ipv6: remove null_entry before adding default route")
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Thought I'd try my luck getting one more in:
- Two fixes for Tegra (one is to common code, but our userspace doesn't hit it).
- One for NV5x-class MCPs

* 'linux-4.15' of git://github.com/skeggsb/linux:
  drm/nouveau/mmu/mcp77: fix regressions in stolen memory handling
  drm/nouveau/bar/gk20a: Avoid bar teardown during init
  drm/nouveau/drm/nouveau: Pass the proper arguments to nvif_object_map_handle()

Commit b05229f4 ("gre6: Cleanup GREv6 transmit path,
call common GRE functions") moved dev->mtu initialization
from ip6gre_tunnel_setup() to ip6gre_tunnel_init(), as a
result, the previously set values, before ndo_init(), are
reset in the following cases:

* rtnl_create_link() can update dev->mtu from IFLA_MTU
  parameter.

* ip6gre_tnl_link_config() is invoked before ndo_init() in
  netlink and ioctl setup, so ndo_init() can reset MTU
  adjustments with the lower device MTU as well, dev->mtu
  and dev->hard_header_len.

  Not applicable for ip6gretap because it has one more call
  to ip6gre_tnl_link_config(tunnel, 1) in ip6gre_tap_init().

Fix the first case by updating dev->mtu with 'tb[IFLA_MTU]'
parameter if a user sets it manually on a device creation,
and fix the second one by moving ip6gre_tnl_link_config()
call after register_netdevice().

Fixes: b05229f4 ("gre6: Cleanup GREv6 transmit path, call common GRE functions")
Fixes: db2ec95d ("ip6_gre: Fix MTU setting")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a new LPM tree is created, we try to replace the trees in the
existing virtual routers with it. If we fail, the tree needs to be
freed.

Currently, this does not happen in the unlikely case where we fail to
bind the tree to the first virtual router, since its reference count
never transitions from 1 to 0.

Fix that by taking a reference before binding the tree.

Fixes: fc922bb0 ("mlxsw: spectrum_router: Use one LPM tree for all virtual routers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Fixes addition of stolen memory base address to PTEs.
- Removes support for compression.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Tested-by: Pierre Moreau <pierre.morrow@free.fr>

Commit bbb163e1 ("drm/nouveau/bar: implement bar1 teardown")
introduced add a teardown helper function for BAR1. During
initialisation of the Nouveau, initially all the teardown helpers are
called once, before calling their init counterparts. For gk20a, after
the BAR1 teardown function is called, the device is hanging during the
initialisation of the FB sub-device. At this point it is unclear why
this is happening and this is still under investigation. However, this
change is preventing Tegra124 devices from booting when Nouveau is
enabled. To allow Tegra124 to boot, remove the teardown helper for
gk20a.

This is based upon a previous patch by Guillaume Tucker but limits
the workaround to only gk20a GPUs.

Fixes: bbb163e1 ("drm/nouveau/bar: implement bar1 teardown")
Reported-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

This is obviously wrong in the current code. Make sure to record the
correct size of the arguments and pass the actual arguments to the
nvif_object_map_handle() function.
Suggested-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

syzbot reported yet another crash [1] that is caused by
insufficient validation of DODGY packets.

Two bugs are happening here to trigger the crash.

1) Flow dissection leaves with incorrect thoff field.

2) skb_probe_transport_header() sets transport header to this invalid
thoff, even if pointing after skb valid data.

3) qdisc_pkt_len_init() reads out-of-bound data because it
trusts tcp_hdrlen(skb)

Possible fixes :

- Full flow dissector validation before injecting bad DODGY packets in
the stack.
 This approach was attempted here : https://patchwork.ozlabs.org/patch/
861874/

- Have more robust functions in the core.
  This might be needed anyway for stable versions.

This patch fixes the flow dissection issue.

[1]
CPU: 1 PID: 3144 Comm: syzkaller271204 Not tainted 4.15.0-rc4-mm1+ #49
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:17 [inline]
 dump_stack+0x194/0x257 lib/dump_stack.c:53
 print_address_description+0x73/0x250 mm/kasan/report.c:256
 kasan_report_error mm/kasan/report.c:355 [inline]
 kasan_report+0x23b/0x360 mm/kasan/report.c:413
 __asan_report_load2_noabort+0x14/0x20 mm/kasan/report.c:432
 __tcp_hdrlen include/linux/tcp.h:35 [inline]
 tcp_hdrlen include/linux/tcp.h:40 [inline]
 qdisc_pkt_len_init net/core/dev.c:3160 [inline]
 __dev_queue_xmit+0x20d3/0x2200 net/core/dev.c:3465
 dev_queue_xmit+0x17/0x20 net/core/dev.c:3554
 packet_snd net/packet/af_packet.c:2943 [inline]
 packet_sendmsg+0x3ad5/0x60a0 net/packet/af_packet.c:2968
 sock_sendmsg_nosec net/socket.c:628 [inline]
 sock_sendmsg+0xca/0x110 net/socket.c:638
 sock_write_iter+0x31a/0x5d0 net/socket.c:907
 call_write_iter include/linux/fs.h:1776 [inline]
 new_sync_write fs/read_write.c:469 [inline]
 __vfs_write+0x684/0x970 fs/read_write.c:482
 vfs_write+0x189/0x510 fs/read_write.c:544
 SYSC_write fs/read_write.c:589 [inline]
 SyS_write+0xef/0x220 fs/read_write.c:581
 entry_SYSCALL_64_fastpath+0x1f/0x96

Fixes: 34fad54c ("net: __skb_flow_dissect() must cap its return value")
Fixes: a6e544b0 ("flow_dissector: Jump to exit code in __skb_flow_dissect")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2018-01-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.15

One last set of fixes for regression submitted during the last few days.

bcma & ssb

* fix older build problems which (apparently) recently became more
  frequent in certain MIPS configurations

brcmfmac

* continue driver initialisation even if CLM blob (firmware) file is
  not found
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since enums do not get converted by the TRACE_EVENT macro into their values,
the event format displaces the enum name and not the value. This breaks
tools like perf and trace-cmd that need to interpret the raw binary data. To
solve this, an enum map was created to convert these enums into their actual
numbers on boot up. This is done by TRACE_EVENTS() adding a
TRACE_DEFINE_ENUM() macro.

Some enums were not being converted. This was caused by an optization that
had a bug in it.

All calls get checked against this enum map to see if it should be converted
or not, and it compares the call's system to the system that the enum map
was created under. If they match, then they call is processed.

To cut down on the number of iterations needed to find the maps with a
matching system, since calls and maps are grouped by system, when a match is
made, the index into the map array is saved, so that the next call, if it
belongs to the same system as the previous call, could start right at that
array index and not have to scan all the previous arrays.

The problem was, the saved index was used as the variable to know if this is
a call in a new system or not. If the index was zero, it was assumed that
the call is in a new system and would keep incrementing the saved index
until it found a matching system. The issue arises when the first matching
system was at index zero. The next map, if it belonged to the same system,
would then think it was the first match and increment the index to one. If
the next call belong to the same system, it would begin its search of the
maps off by one, and miss the first enum that should be converted. This left
a single enum not converted properly.

Also add a comment to describe exactly what that index was for. It took me a
bit too long to figure out what I was thinking when debugging this issue.

Link: http://lkml.kernel.org/r/717BE572-2070-4C1E-9902-9F2E0FEDA4F8@oracle.com

Cc: stable@vger.kernel.org
Fixes: 0c564a53 ("tracing: Add TRACE_DEFINE_ENUM() macro to map enums to their values")
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Teste-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

A cleanup of the PM code left an incorrect #ifdef in place, leading
to a harmless build warning:

drivers/net/ethernet/intel/fm10k/fm10k_pci.c:2502:12: error: 'fm10k_suspend' defined but not used [-Werror=unused-function]
drivers/net/ethernet/intel/fm10k/fm10k_pci.c:2475:12: error: 'fm10k_resume' defined but not used [-Werror=unused-function]

It's easier to use __maybe_unused attributes here, since you
can't pick the wrong one.

Fixes: 8249c47c ("fm10k: use generic PM hooks instead of legacy PCIe power hooks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In bringing back the context checks, the code checks first if its normal
(non-interrupt) context, and then for NMI then IRQ then softirq. The final
check is redundant. Since the if branch is only hit if the context is one of
NMI, IRQ, or SOFTIRQ, if it's not NMI or IRQ there's no reason to check if
it is SOFTIRQ. The current code returns the same result even if its not a
SOFTIRQ. Which is confusing.

  pc & SOFTIRQ_OFFSET ? 2 : RB_CTX_SOFTIRQ

Is redundant as RB_CTX_SOFTIRQ *is* 2!

Fixes: a0e3a18f ("ring-buffer: Bring back context level recursive checks")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>