This patch adds support System MMU which supports address transition
from virtual address to physical address. Basically, each hardware
block is connected System MMU block can use directly vitrual address
when it accesses physical memory not using physical address.
Signed-off-by: Donguk Ryu <du.ryu@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
[kgene.kim@samsung.com: removed useless codes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Swap device and driver names in serial/samsung.c
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch adds support for clock information exposed to debug-fs interface.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
[kgene.kim@samsung.com: removed useless empty lines]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Both S3C2443 and S3C2416 support 4 UART channels, this patch adds support
for the missing uart channel.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

There are few functions marked as __init, but exported to modules in
devices declaration files.

s3c_nand_set_platdata() and s3c24xx_ts_set_platdata() are used only by
boards init code now, so remove EXPORT_SYMBOL() for them.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

S3C2443 has two-bits pull-up/pull-down configuration fields in GPIO
registers, but values are differ from other SoCs with two-bits
configuration. gpio-cfg-helpers.h already has prototypes for
s3c2443-style pull-up/down methods, so implement them.
Signed-off-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Enable card detect by GPIO pin on hsmmc1 device (SD0 on SMDK2416 board)
and enable card polling on hsmmc0 (SD1).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Samsung S3C2416 has two SDHCI controllers compatible with other
Samsung's SoCs (S3C64XX, S5PC100 etc...).

Add required platform setup code that the devices can be used with
sdhci-s3c driver.
Signed-off-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
[kgene.kim@samsung.com: change to __raw_{readl,writel} from {readl,writel}]
[kgene.kim@samsung.com: build error fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Define maps for HSMMC devices.

S3C2443 has one HSMMC device with base address 0x4A800000.
S3C2416 has HSMMC0 at 0x4AC00000 and HSMMC1 at 0x4A800000.

So suppose that S3C2443 has only HSMMC1.

Define clock for hsmmc0 device and register it.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch changes the clock registration code to use the s3c_register_clocks()
followed by s3c_disable_clocks() instead of the loops it was using and cleanups
the return of s3c24xx_register_clocks() because it includes it.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch changes the clock registration code to use the s3c_register_clocks()
followed by s3c_disable_clocks() instead of the loops it was using and cleanups
the return of s3c24xx_register_clocks() because it includes it.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch changes the clock registration code to use the s3c_register_clocks()
followed by s3c_disable_clocks() instead of the loops it was using.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch changes the clock registration code to use the s3c_register_clocks()
followed by s3c_disable_clocks() instead of the loops it was using.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch changes the clock registration code to use the s3c_register_clocks()
followed by s3c_disable_clocks() instead of the loops it was using.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch changes the clock registration code to use the s3c_register_clocks()
followed by s3c_disable_clocks() instead of the loops it was using.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch changes the clock registration code to use the s3c_register_clocks()
followed by s3c_disable_clocks() instead of the loops it was using.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The stop function sets the DMA_HALT bit, which prevents
the DMA transfer to resume after stop, for example during
audio PAUSE/PLAY cycle. Clear the HALT bit during start.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

When GENERIC_HARDIRQS_NO_DEPRECATED is enabled, a number of struct
irq_desc members stop being directly accessible, and need to be
accessed via the irq_data struct instead -- this patch fixes up the
plat-samsung sites that still access those members directly.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
[kgene.kim@samsung.com: coding-style fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Conflicts:
	arch/arm/mach-s5pv310/Makefile

Conflicts:
	arch/arm/mach-s5pv310/Kconfig
	arch/arm/mach-s5pv310/Makefile
	arch/arm/mach-s5pv310/mach-smdkc210.c
	arch/arm/mach-s5pv310/mach-smdkv310.c
	arch/arm/plat-samsung/include/plat/devs.h

Conflicts:
	arch/arm/mach-s5pv210/mach-smdkv210.c

There may be up to two MIPI CSI slave interfaces depending on the SoC version.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add IRQ and register base address definitions for MIPI CSI slave devices.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Naming changed for consistency with s5pv310 where there are two instances
of the device.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch adds DM9000 Ethernet Controller device support for SMDKV210.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch adds the SROM controller clock to the list of clocks to be enabled at
boot time. It is required to be enabled at boot time since the modules connected
over the SROM interface such as the Ethernet controller need an operational SROM.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch modifies the following.

1. Moves the SROM controller mapping from S5PV210 specific code to
   S5P common code. The SROM controller mapping can be used for all
   S5P SoCs.

2. Define the SROM controller physical address for S5P64X0, S5P6442,
   S5PC100, S5PV210 and S5PV310.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Some of the S5P platforms like S5PC100 and S5PV210 include SROM banks
4 and 5 in addition to SROM banks 0 to 3. This patch adds register
offsets for SROM bank 4 and 5.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>