It is perfectly valid for some hwmod to not have any
register target address for sysconfig. This is especially
true for interconnect hwmods.
Remove the warning.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The Type 2 type of IPs will not have any enawakeup bit in their sysconfig.
Writing to that bit will instead trigger a softreset.
Check the flag to write this bit only if the module supports it.
Reported-by: Miguel Vadillo <vadillo@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

When calling the shutdown, the module may be already in idle.
Accessing the sysconfig register will then lead to a crash.
In that case, re-enable the module in order to allow the access
to the sysconfig register.
Signed-off-by: Miguel Vadillo <vadillo@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Add the flag to every IPs that support it to allow the
framework to enable it instead of the SMART_STANDBY default
mode.
Without that, an IP with busmaster capability will not
be able to wakeup the interconnect at all.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The commit 86009eb3 was adding
the wakeup support for new OMAP4 IPs. This support is incomplete for
busmaster IPs that need as well to use smart-standby with wakeup.

This new standbymode is suported on HSI and USB_HOST_FS for the moment.

Add the new MSTANDBY_SMART_WKUP flag to mark the IPs that support this
capability.

Enable this new mode when applicable in _enable_wakeup, _disable_wakeup,
_enable_sysc and _idle_sysc.

The omap_hwmod_44xx_data.c will have to be updated to add this new flag.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Djamil Elaidi <d-elaidi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Merge branch 'cleanup-part-2' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into omap/cleanup

Merge branch 'peter/topic/for-tony_mach-cleanup' of git://gitorious.org/omap-audio/linux-audio into cleanup-part-2

These McBSP port number enums are used only in two places in the McBSP code
so we may remove then and just use numeric values like rest of the code does.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

These variables got unused after ("omap: mcbsp: Drop in-driver transfer
support") but was noticed only afterwards.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Some regulator config can be moved out from board files,
since they are close to identical.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Reduce the amount of duplicated code by moving the common
configuration for twl4030/5030/tpsxx to the twl-common file.
Use the omap3_pmic_get_config function from board files to
properly configure the PMIC with the common fields.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Reduce the amount of duplicated code by moving the common
configuration for TWL6030 (on OMAP4 platform) to the
twl-common file.
Use the omap4_pmic_get_config function from board files to
properly configure the PMIC with the common fields.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Introduce a new file, which will be used to configure
common pmic (TWL) devices, regulators, and TWL audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

board-generic.c now contains a reference to omap3_timer, but depends
only on ARCH_OMAP2, not on ARCH_OMAP3, which controls that symbol.
omap2_timer seems to be more appropriate anyway, so use that instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>

Merge branch 'for_3.1/pm-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into devel-cleanup

Conflicts:
	arch/arm/mach-omap2/pm-debug.c
	arch/arm/mach-omap2/pm.h

We haven't seen either use for in-driver transfer API in McBSP driver
over the years so it looks they can be removed too.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We haven't seen any use for the SPI API in McBSP driver over the years. More
over, Peter Ujfalusi <peter.ujfalusi@ti.com> noticed that SPI mode is not
even supported since OMAP2430 so it's very unlikely that we'll see any use
for it in the future either.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix compilation error introduced with 786b01a8
(cleanup regulator supply definitions in mach-omap2).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap_nand_platform_data fields 'options', 'gpio_irq', 'nand_setup' and
'dma_channel' are never referenced by the NAND driver, yet various
board files are initializing those fields. This is both incorrect and
confusing, so remove them. This allows to get rid of a global
variable in gpmc-nand.c.

This also corrects an issue where some boards are trying to pass NAND
16bit flag through .options, but the driver is using .devsize instead
and ignoring .options.

Finally, .dev_ready is treated as a flag by the driver, so make it bool
instead of a function pointer.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can keep everything sys_timer and gptimer.c related code in
timer.c as the code will be very minimal.

Later on we can also remove timer-mpu.c, as it can be called from
omap4_timer_init function.

This allows us to get rid of confusing existing files. We currently
have timer-gp.c, timer-mpu.c, and patches have been posted to add
dmtimer.c. There's no need to have these multiple files, we can
put everything into timer.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>

This is no longer needed as we now just set the desired
.timer in MACHINE_START. We can now also remove timer-gp.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

Use dmtimer macros for clocksource. As with the clockevent,
this allows us to initialize the rest of dmtimer code later on.

Note that eventually we will be initializing the timesource
from init_early so sched_clock will work properly for
CONFIG_PRINTK_TIME.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

There's no need to initialize the dmtimer framework early.
Just mark the clocksource and timesource as reserved, and
initialize dmtimer with an arch_initcall.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

Fix the section mismatch warning:

  WARNING: vmlinux.o(.text+0x21118): Section mismatch
  in reference from the function pm_dbg_init() to the
  function .init.text:pwrdms_setup()
  The function pm_dbg_init() references
  the function __init pwrdms_setup().
  This is often because pm_dbg_init lacks a __init
  annotation or the annotation of pwrdms_setup is wrong.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Remove OMAP3-specific register dumping feature from PM debug layer.
This is removed because:

- it's ugly
- it's OMAP3-specific, and will obviously not scale to OMAP4+
- userspace /dev/mem-based tools (like omapconf) can do this much better
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Remove the OMAP-specific PM debug 'sleep_while_idle' feature which is
currently available as an OMAP-specific debugfs entry.

This duplicates existing ARM-generic functionality available as a
boot-time option using the boot cmdline option 'hohlt'.

If runtime configuration of this is needed, then adding a debugfs
entry for the ARM-generic hlt/nohlt interface should be added.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Error label case seems to have a 2 tab indentation when just 1 is
necessary.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Since we already know the state of the autocomp enablement, we can
see if the requested state is different from the current state and
enable/disable SR only on the need basis.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

We will enable and disable interrupt on a need basis in the class
driver. We need to keep the IRQ disabled by default else the
forceupdate or vcbypass events could trigger events that we don't
need/expect to handle.

This is a preparation for SmartReflex AVS class drivers such as
class 2 and class 1.5 which would need to use interrupts. Existing
SmartReflex AVS class 3 driver does not require to use interrupts
and is not impacted by this change.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Interrupt notification mechanism of SmartReflex can be used by the
choice of implementation of the class driver. For example, Class 2 and
Class 1.5 of SmartReflex can both use the interrupt notification to
identify the transition of voltage or other events.

Hence, the actual class does not matter for notifier. Let the class
driver's handling decide how it should be used. SmartReflex driver
should provide just the primitives.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

This removes the support for setting the wake-up timer for debugging.

Later on we can reserve gptimer1 for PM code only and have similar
functionality.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

This patch makes timer-gp.c to use only a subset of dmtimer
functions without the need to initialize dmtimer code early.

Also note that now with the inline functions, timer_set_next_event
becomes more efficient in the lines of assembly code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

This will allow us to share the code between system timer and
dmtimer device driver code without having to initialize all the
dmtimers early. This change will also make the timer_set_next_event
more efficient as the inline functions will optimize the code
better for the timer reprogramming.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

These will be needed when dmtimer platform init code gets split
for omap1 and omap2+. These will also be needed for separate
sys_timer init and driver init for the rest of the hardware timers
in the following patches. No functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

This is needed for the following patches so we can initialize the
rest of the hardware timers later on.

As with the init_irq calls, there's no need to do cpu_is_omap calls
during the timer init as we only care about the major omap generation.
This means that we can initialize the sys_timer with the .timer
entries alone.

Note that for now we just set stubs for the various sys_timer entries
that will get populated in a later patch. The following patches will
also remove the omap_dm_timer_init calls and change the init for the
rest of the hardware timers to happen with an arch_initcall.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

This allows us to remove cpu_is_omap calls from init_irq functions.
There should not be any need for cpu_is_omap calls as at this point.
During the timer init we only care about SoC generation, and not about
subrevisions.

The main reason for the patch is that we want to initialize only
minimal omap specific code from the init_early call.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

When runtime PM is disabled, device clocks need to be enabled on
device add and disabled on device remove.  This currently is not
happening because in the !PM_RUNTIME case, no notifiers are registered
for OMAP1 devices.

Fix this by ensuring notifiers are registered, even in the !PM_RUNTIME case.
Reported-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>