- 18 Sep, 2017 1 commit
-
-
Haneen Mohammed authored
This patch replace instances of dev_info/err/debug with DRM_DEV_INFO/ERROR/WARN respectively inorder to use a drm-formatted specific log messages. Issue corrected with the help of the following Coccinelle script: @r@ @@ ( -dev_info +DRM_DEV_INFO | -dev_err +DRM_DEV_ERROR | -dev_dbg +DRM_DEV_DEBUG ) Signed-off-by:
Haneen Mohammed <hamohammed.sa@gmail.com> Signed-off-by:
Mark Yao <mark.yao@rock-chips.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170915083603.GA18992@Haneen
-
- 16 Sep, 2017 7 commits
-
-
Noralf Trønnes authored
No need to put out a driver registered message since drm_dev_register() does that now. SPI speed is an important metric when dealing with display problems, so retain that info. Cc: David Lechner <david@lechnology.com> Signed-off-by:
Noralf Trønnes <noralf@tronnes.org> Acked-by:
David Lechner <david@lechnology.com> Link: https://patchwork.freedesktop.org/patch/msgid/1504883250-43487-8-git-send-email-noralf@tronnes.org
-
Noralf Trønnes authored
GEM lookup failure can easily be triggered by userspace so make it a debug message, not an error message. Also remove unnecessary inner parentheses and fix alphabetical struct declaration order. Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/1505147865-18194-2-git-send-email-noralf@tronnes.org
-
Noralf Trønnes authored
drm_fb_cma_create() and drm_fb_cma_prepare_fb() are just wrappers now, use drm_gem_fb_create() and drm_gem_fb_prepare_fb() directly. Cc: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Link: https://patchwork.freedesktop.org/patch/msgid/1502631125-13557-11-git-send-email-noralf@tronnes.org
-
Lars-Peter Clausen authored
The HDMI codec platform data is global driver state shared by all instances. As such it should not be modified (and is not), to make this explicit declare it as const. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Tested-by:
John Stultz <john.stultz@linaro.org> Signed-off-by:
Archit Taneja <architt@codeaurora.org> Link: https://patchwork.freedesktop.org/patch/msgid/20170905121018.11477-4-lars@metafoo.de
-
Lars-Peter Clausen authored
Fall back to polling the connector for connect and disconnect events when no interrupt is specified. Otherwise these events will not be noticed and monitor hotplug does not work. Signed-off-by:
-
Lars-Peter Clausen authored
The adv7511 driver keeps a private copy of the EDID in its driver state struct. But this copy is only used in adv7511_get_modes() where it is also retrieved, so there is no need to keep this extra copy around. If a need to access the EDID elsewhere in the driver ever arises the copy that is stored in the connector can be used. This copy is accessible through drm_connector_get_edid(). Note, this patch removes the NULL check of the EDID before passing it to drm_detect_hdmi_monitor(), but that is fine since the function correctly handles the case where the EDID is NULL. Signed-off-by:
-
Lars-Peter Clausen authored
Currently adv7511_get_modes() bails out early when no EDID could be retrieved. This leaves the previous EDID in place, which is typically not the intended behavior and might confuse applications. Instead the EDID should be cleared when no EDID could be retrieved. All functions that are called after the EDID check handle the case where the EDID is NULL just fine and exhibit the expected behavior, so just drop the check. Signed-off-by:
-
- 13 Sep, 2017 6 commits
-
-
Maarten Lankhorst authored
Pass DRM_MODESET_ACQUIRE_INTERRUPTIBLE to acquire_init, and handle drm_modeset_backoff which can now fail by returning the error. Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20170912133749.6532-7-maarten.lankhorst@linux.intel.comReviewed-by:
Emil Velikov <emil.l.velikov@gmail.com>
-
Maarten Lankhorst authored
Pass DRM_MODESET_ACQUIRE_INTERRUPTIBLE to acquire_init, and handle drm_modeset_backoff which can now fail by returning the error. Signed-off-by:
-
Maarten Lankhorst authored
Pass DRM_MODESET_ACQUIRE_INTERRUPTIBLE to acquire_init, and handle drm_modeset_backoff which can now fail by returning the error. Signed-off-by:
-
Maarten Lankhorst authored
Pass DRM_MODESET_ACQUIRE_INTERRUPTIBLE to acquire_init, and handle drm_modeset_backoff which can now fail by returning the error. Signed-off-by:
-
Maarten Lankhorst authored
Pass DRM_MODESET_ACQUIRE_INTERRUPTIBLE to acquire_init, and handle drm_modeset_backoff which can now fail by returning the error. Signed-off-by:
-
Maarten Lankhorst authored
When we want to make drm_atomic_commit interruptible, there are a lot of places that call the lock function, which we don't have control over. Rather than trying to convert every single one, it's easier to toggle interruptible waiting per acquire_ctx. If drm_modeset_acquire_init is called with DRM_MODESET_ACQUIRE_INTERRUPTIBLE, then we will perform interruptible waits in drm_modeset_lock and drm_modeset_backoff. Changes since v1: - Fix locking example in drm_modeset_lock.c to be compatible with interruptible waiting (xexaxo) and make it default. Uninterruptible waiting shouldn't happen except in corner cases, but the example will still apply if the flag is removed. - Add drm_modeset_lock_single_interruptible() to documentation. - Fix dead link to removed drm_modeset_lock_interruptible() in drm_modeset_lock(). Signed-off-by:
-
- 11 Sep, 2017 6 commits
-
-
Linus Walleij authored
This makes use of the drm_simple_display_pipe_attach_bridge() call and removes the two calls removing the bridge, which were erroneous: they unregister the bridge which is not what we want, we just want to unreference it and that is already handled by the core. Reviewed-by:
Eric Anholt <eric@anholt.net> Acked-by:
Linus Walleij <linus.walleij@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20170910220801.28588-1-linus.walleij@linaro.org
-
Daniel Vetter authored
We're using this for outreachy, unfortunately someone already tried to look at a task that was done already :-( Update them all. Cc: Sean Paul <seanpaul@chromium.org> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Signed-off-by:
Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20170911065151.22672-1-daniel.vetter@ffwll.ch
-
Dhinakaran Pandiyan authored
The POWER_DOWN_PHY and POWER_UP_PHY sideband message transactions allow the source to reqest any node in a mst path or a whole path to be powered down or up. This allows drivers to target a specific sink in the MST topology, an improvement over just power managing the imediate downstream device. Secondly, since the request-reply protocol waits for an ACK, we can be sure that a downstream sink has enough time to respond to a power up/down request. v2: Fix memory leak (Lyude) Cc: Lyude <lyude@redhat.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Harry Wentland <harry.wentland@amd.com> Signed-off-by:
Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170907001458.9399-1-dhinakaran.pandiyan@intel.comReviewed-by:
Lyude Paul <lyude@redhat.com> Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com>
-
Ville Syrjälä authored
Make __drm_object_property_get_value() static to fix the following sparse warning: drm_mode_object.c:250:5: warning: symbol '__drm_object_property_get_value' was not declared. Should it be static? Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Fixes: 4a97a3da ("drm: Don't update property values for atomic drivers") Signed-off-by:
Thierry Reding <treding@nvidia.com>
-
Ville Syrjälä authored
drm_get_link_status_name() isn't used so kill it. Fixes the following sparse warning: drm_connector.c:618:1: warning: symbol 'drm_get_link_status_name' was not declared. Should it be static? Cc: Manasi Navare <manasi.d.navare@intel.com> Fixes: 40ee6fbe ("drm: Add a new connector atomic property for link status") Signed-off-by:
-
Ville Syrjälä authored
Fix the following sparse warnings by making functions static: drm_syncobj.c:420:5: warning: symbol 'drm_syncobj_import_sync_file_fence' was not declared. Should it be static? drm_syncobj.c:441:5: warning: symbol 'drm_syncobj_export_sync_file' was not declared. Should it be static? Cc: Dave Airlie <airlied@redhat.com> Fixes: 3ee45a3b ("drm/syncobj: add sync_file interaction. (v1.2)") Signed-off-by:
-
- 10 Sep, 2017 7 commits
-
-
Linus Walleij authored
The ARM reference designs in the Versatile family: Integrator, Versatile and RealView can make use of the new DRM driver as well. We just need to create a bit of platform-specific code for them that we isolate to its own file. Reviewed-by:
-
Linus Walleij authored
The silcon and components around the PL111 may require some variants to perform special set-up of the display. Add two callbacks to manage this. Reviewed-by:
-
Linus Walleij authored
The old codebase has a delay between enabling and powering up the PL11x. According to the manual for PL110, ARM DDI 0161E page 1-5 and the PL111 manual ARM DDI 0293C page 1-6, the power sequence should be such that once Vdd is stable (which we assume it is at boot) LCDEN is enabled first and then CLPOWER should be enabled "after the signals have stabilized" and this is said to be display-dependent. The old codebase uses 20ms. Reviewed-by:
-
Linus Walleij authored
We detect and enable the use of the PL110 variant, an earlier incarnation of PL111. The only real difference is that the control and interrupt enable registers have swapped place. The Versatile AB and Versatile PB have a variant inbetween PL110 and PL111, it is PL110 but they have already swapped the two registers so those two need a bit of special handling. Reviewed-by:
-
Linus Walleij authored
This replaces the custom connector in the PL111 with the panel bridge helper. This works nicely for all standard panels, but since there are several PL11x-based systems that will need to use the dumb VGA connector bridge we use drm_of_find_panel_or_bridge() and make some headroom for dealing with bridges that are not panels as well, and drop a TODO in the code. Reviewed-by:
-
Linus Walleij authored
This adds all the main control registers to the debugfs register file. This was helpful for my debugging so it will likely help others as well. Reviewed-by:
-
Linus Walleij authored
The header file contains prototypes for two nonexisting functions. Get rid of them. Reviewed-by:
-
- 09 Sep, 2017 7 commits
-
-
Noralf Trønnes authored
drm_fb_cma_create() is just a wrapper around drm_gem_fb_create() now, so use the function directly. Cc: Jyri Sarha <jsarha@ti.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
Jyri Sarha <jsarha@ti.com> Link: https://patchwork.freedesktop.org/patch/msgid/1502631125-13557-20-git-send-email-noralf@tronnes.org
-
Chen-Yu Tsai authored
If we want to have vblank on both pipelines at the same time, we need to call drm_vblank_init with num_crtcs = 2. Instead, since the crtc init calls correctly set mode_config.num_crtc, we can move the drm_vblank_init call to after the crtc init code is called, which is the component bind part. Then we can just pass mode_config.num_crtc in. Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170908075016.18657-8-wens@csie.org
-
Chen-Yu Tsai authored
The TCON has a mux to select the source of the data to display. This mux includes selecting the display backends. On the A31, which has two display pipelines, this mux can let the TCON select either backend as its data source. Although the muxing can be changed on the fly, DRM needs to be able to group a bunch of layers such that they get switched to another crtc together. This is because the display backend does the layer compositing, while the TCON generates the display timings. This constraint is not supported by DRM. Here we simply pair up backends and TCONs with the same ID. Signed-off-by:
-
Chen-Yu Tsai authored
Now that sun4i_tcon_find_engine_traverse() usage is restricted to the single input case, we can remove the for_each_available_child_of_node loop. While at it, consolidate all the of_node_put calls into a common exit path. Signed-off-by:
-
Chen-Yu Tsai authored
The device tree binding for sun4i-drm says: For all connections between components up to the TCONs in the display pipeline, when there are multiple components of the same type at the same depth, the local endpoint ID must be the same as the remote component's index. For example, if the remote endpoint is Frontend 1, then the local endpoint ID must be 1. We should be able to get the TCON's ID directly from any of the remote endpoints from its input port. With the ID, we can then go through the list of registered engines and find a matching one by ID. However the A31 device tree is incorrect. We assumed that there were no cross pipeline connections between the backends and TCONs. As a result, in all the endpoints between the backends and TCONs of the second display pipeline, the endpoint IDs were incorrectly set to 0, when in fact they should've been set to 1. To maintain compatibility with this incorrect device tree, we first check if the TCON's input port has 1 or many endpoints. If there are more than 1, then it is likely a fixed version, and we can proceed with the new method. If there is only 1 endpoint, then it is possibly an incorrect version, or it could be the SoC only has one pipeline. In either case we fall back to using the old method of traversing the input connections to find a matching engine, and then get its ID. Signed-off-by: -
Chen-Yu Tsai authored
The patch b317fa3b ("drm/sun4i: tcon: Find matching display backend by device node matching") assumed a one-to-one mapping between TCONs and backends. This turned out wrong, as we found muxing controls in the TCON of the A31, and undocumented usage of the backend output selector of the A20. Make sun4i_tcon_find_engine() bail out if the current node has multiple input connections. Fixes: b317fa3b ("drm/sun4i: tcon: Find matching display backend by device node matching") Signed-off-by:
-
Chen-Yu Tsai authored
The encoder drivers use drm_of_find_possible_crtcs to get upstream crtcs from the device tree using of_graph. For the results to be correct, encoders must be probed/bound after _all_ crtcs have been created. The existing code uses a depth first recursive traversal of the of_graph, which means the encoders downstream of the TCON get add right after the first TCON. The second TCON or CRTC will never be properly associated with encoders connected to it. Other platforms, such as Rockchip, deal with this by probing all CRTCs first, then all subsequent components. This is easy to do since the CRTCs correspond to just one device node, and are the first nodes in the pipeline. However with Allwinner SoCs, the function of the CRTC is split between the display backend (DE 1.0) or mixer (DE 2.0), which does scan-out and compositing, and the TCON, which generates the display timing signals. Further complicating the process, there may be a Dynamic Range Controller between the backend and the TCON. Also, the backend is preceded by the frontend, with a Display Enhancement Unit possibly in between. In a dual display pipeline setup, both frontends can feed either backend, and both backends can feed either TCON. We want all components of the same type to be added before the next type in the pipeline. Fortunately, the pipelines are perfectly symmetric, i.e. components of the same type are at the same depth when counted from the frontend. The only exception is the third pipeline in the A80 SoC, which we do not support anyway. Hence we can use a breadth first search traversal order to add components. We do not need to check for duplicates. The component matching system handles this for us. Signed-off-by:
-
- 08 Sep, 2017 6 commits
-
-
Chen-Yu Tsai authored
When binding the TCON, we were checking the reset control status and asserting reset if it wasn't in reset. The check failed to account for the reset control API returning error codes if the status callback was not implemented. Since we want the TCON to be reset in all cases, use reset_control_reset to force a reset instead. Fixes: 9026e0d1 ("drm: Add Allwinner A10 Display Engine support") Signed-off-by:
-
Maxime Ripard authored
sun4i-drm is maintained in drm-misc as a small driver. Signed-off-by:
-
Dominik Behr authored
To avoid hanging userspace components that might have been waiting on the active fences of the destroyed timeline we need to signal with error all remaining fences on such timeline. This restore the default behaviour of the Android sw_sync framework, which Android still relies on. It was broken on the dma fence conversion a few years ago and never fixed. v2: Do not bother with cleanup do the list (Chris Wilson) Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Dominik Behr <dbehr@chromium.org> Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170907190246.16425-2-gustavo@padovan.org
-
Colin Ian King authored
The current error handling when devm_kzalloc fails performs a non-null check on connector which is redundant because connector is null at that failure point. Once this is removed, make the failure path into a trivial -ENOMEM return to clean up the error handling. Also remove need to initialize connector to NULL. Detected by CoverityScan CID#1339527 ("Logically dead code") Signed-off-by:Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Sean Paul authored
Now that we have the DRM_DEV_* variants, we should use them. Signed-off-by:
-
Maarten Lankhorst authored
Now that the last users have been converted, we can finally get rid of for_each_obj_in_state, we have better macros to replace them with. Signed-off-by:
-
