Spec sheet states that the TDA19988 supports up to 165MHz dotclock
speeds. Without this change modes higher than 1080p are un-attainable.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

tda998x uses drm_connector_register() in the .bind function that
needs to be balanced with a drm_connector_unregister() in the .unbind.
Otherwise dangling sysfs entries are left behind and future rebinds
will fail.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We can now kill a number of glue functions which were sitting between
the common tda998x code and the drm encoder/connector methods.  This
results in slightly cleaner code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Kill the redundant tda998x_priv2 structure now that its only member is
the struct tda998x_priv.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Move the DRM connector structure into struct tda998x_priv from the old
struct tda998x_priv2.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Remove the encoder pointer from struct tda998x_priv, moving the encoder
itself from struct tda998x_priv2 here.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Remove the DRM slave encoder compatibility from the TDA998x driver.  We
now use the component helpers to manage the binding of DRM sub-drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

As reading the interrupt registers clears the outstanding interrupts, we
must process all received interrupts to avoid dropping any.  Rearrange
the code to achieve this, and properly check for a HPD interrupt from
the CEC_RXSHPDINT register.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

C99 types are against the style of the Linux kernel.  Convert to using
Linus-friendly types.  See https://lwn.net/Articles/113367/ for more
information.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit 6833d26e ("drm: tda998x: Fix EDID read timeout on HDMI
connect") used a weak scheme to try and delay reading EDID on a HDMI
connect event.  It is weak because delaying the notification of a
hotplug event does not stop userspace from trying to read the EDID
within the 100ms delay.

The solution provided here solves this issue:
* When a HDMI connection event is detected, mark a blocking flag for
  EDID reads, and start a timer for the delay.
* If an EDID read is attempted, and the blocking flag is set, wait
  for the blocking flag to clear.
* When the timer expires, clear the blocking flag and wake any thread
  waiting for the EDID read.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Rather than always reporting that the interrupt was handled, we should
report whether we did handle the interrupt.  Arrange to report IRQ_NONE
for cases where we found nothing to do.

This allows us to (eventually) recover from stuck-IRQ problems, rather
than causing the kernel to solidly lock up.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

There is no way 'priv' can be NULL in tda998x_irq_thread() - this can
only happen if request_threaded_irq() was passed a NULL priv pointer,
and we would have crashed long before then if that was the case.

We also always ensure that priv->encoder is correctly setup, which
must have been initialised prior to the interrupt being claimed, so we
can remove this check as well.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit cf736ea6 ("thermal: power_allocator: do not use devm*
interfaces") forgot to change a devm_kcalloc() to just kcalloc(), but
it's corresponding devm_kfree() was changed to kfree().  Allocate with
kcalloc() to match the kfree().

Fixes: cf736ea6 ("thermal: power_allocator: do not use devm* interfaces")
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull libata fixlet from Tejun Heo:
 "Simple blacklist entry addition"

* 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  Add factory recertified Crucial M500s to blacklist

Pull sound fixes from Takashi Iwai:
 "Here are stable fixes that have been gathered since rc8: fixes for
  HD-audio widget power control regressions since 4.1, a NULL fix for
  HD-audio HDMI, a noise fix for Conexant codecs and a quirk addition
  for USB-Audio DSD"

* tag 'sound-fix-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Fix path power activation
  ALSA: hda - Check all inputs for is_active_nid_for_any()
  ALSA: hda: fix possible NULL dereference
  ALSA: hda - Shutdown CX20722 on reboot/free to avoid spurious noises
  ALSA: usb: Add native DSD support for Gustard DAC-X20U

Pull powerpc fixes from Michael Ellerman:
 "Fix MSI/MSI-X on pseries from Guilherme"

* tag 'powerpc-4.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/PCI: Disable MSI/MSI-X interrupts at PCI probe time in OF case
  PCI: Make pci_msi_setup_pci_dev() non-static for use by arch code

Pull networking fixes from David Miller:
 "Some straggler bug fixes here:

   1) Netlink_sendmsg() doesn't check iterator type properly in mmap
      case, from Ken-ichirou MATSUZAWA.

   2) Don't sleep in atomic context in bcmgenet driver, from Florian
      Fainelli.

   3) The pfkey_broadcast() code patch can't actually ever use anything
      other than GFP_ATOMIC.  And the cases that right now pass
      GFP_KERNEL or similar will currently trigger an RCU splat.  Just
      use GFP_ATOMIC unconditionally.  From David Ahern.

   4) Fix FD bit timings handling in pcan_usb driver, from Marc
      Kleine-Budde.

   5) Cache dst leaked in ip6_gre tunnel removal, fix from Huaibin Wang.

   6) Traversal into drivers/net/ethernet/renesas should be triggered by
      CONFIG_NET_VENDOR_RENESAS, not a particular driver's config
      option.  From Kazuya Mizuguchi.

   7) Fix regression in handling of igmp_join errors in vxlan, from
      Marcelo Ricardo Leitner.

   8) Make phy_{read,write}_mmd_indirect() properly take the mdio_lock
      mutex when programming the registers.  From Russell King.

   9) Fix non-forced handling in u32_destroy(), from WANG Cong.

  10) Test the EVENT_NO_RUNTIME_PM flag before it is cleared in
      usbnet_stop(), from Eugene Shatokhin.

  11) In sfc driver, don't fetch statistics firmware isn't capable of,
      from Bert Kenward.

  12) Verify ASCONF address parameter location in SCTP, from Xin Long"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  sctp: donot reset the overall_error_count in SHUTDOWN_RECEIVE state
  sctp: asconf's process should verify address parameter is in the beginning
  sfc: only use vadaptor stats if firmware is capable
  net: phy: fixed: propagate fixed link values to struct
  usbnet: Get EVENT_NO_RUNTIME_PM bit before it is cleared
  drivers: net: xgene: fix: Oops in linkwatch_fire_event
  cls_u32: complete the check for non-forced case in u32_destroy()
  net: fec: use reinit_completion() in mdio accessor functions
  net: phy: add locking to phy_read_mmd_indirect()/phy_write_mmd_indirect()
  vxlan: re-ignore EADDRINUSE from igmp_join
  net: compile renesas directory if NET_VENDOR_RENESAS is configured
  ip6_gre: release cached dst on tunnel removal
  phylib: Make PHYs children of their MDIO bus, not the bus' parent.
  can: pcan_usb: don't provide CAN FD bittimings by non-FD adapters
  net: Fix RCU splat in af_key
  net: bcmgenet: fix uncleaned dma flags
  net: bcmgenet: Avoid sleeping in bcmgenet_timeout
  netlink: mmap: fix tx type check

Pull nvdimm fixlet from Dan Williams:
 "This is a libnvdimm ABI fixup.

  I pushed back on this change quite hard given the late date, that it
  appears to be purely cosmetic, sysfs is not necessarily meant to be a
  user friendly UI, and the kernel interprets the reversed polarity of
  the ACPI_NFIT_MEM_ARMED flag correctly.  When this flag is set, the
  energy source of an NVDIMM is not armed and any new writes to the DIMM
  may not be preserved.

  However, Bob Moore warned me that it is important to get these things
  named correctly wherever they appear otherwise we run the risk of a
  less than cautious firmware engineer implementing the polarity the
  wrong way.  Once a mistake like that escapes into production platforms
  the flag becomes useless and we need to move to a new bit position.

  Bob has agreed to take a change through ACPICA to rename
  ACPI_NFIT_MEM_ARMED to ACPI_NFIT_MEM_NOT_ARMED, and the patch below
  from Toshi brings the sysfs representation of these flags in line with
  their respective polarities.

  Please pull for 4.2 as this is the first kernel to expose the ACPI
  NFIT sysfs representation, and this is likely a kernel that firmware
  developers will be using for checking out their NVDIMM enabling"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  nfit: Clarify memory device state flags strings

Commit f8d96052 ("sctp: Enforce retransmission limit during shutdown")
fixed a problem with excessive retransmissions in the SHUTDOWN_PENDING by not
resetting the association overall_error_count.  This allowed the association
to better enforce assoc.max_retrans limit.

However, the same issue still exists when the association is in SHUTDOWN_RECEIVED
state.  In this state, HB-ACKs will continue to reset the overall_error_count
for the association would extend the lifetime of association unnecessarily.

This patch solves this by resetting the overall_error_count whenever the current
state is small then SCTP_STATE_SHUTDOWN_PENDING.  As a small side-effect, we
end up also handling SCTP_STATE_SHUTDOWN_ACK_SENT and SCTP_STATE_SHUTDOWN_SENT
states, but they are not really impacted because we disable Heartbeats in those
states.

Fixes: Commit f8d96052 ("sctp: Enforce retransmission limit during shutdown")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

in sctp_process_asconf(), we get address parameter from the beginning of
the addip params. but we never check if it's really there. if the addr
param is not there, it still can pass sctp_verify_asconf(), then to be
handled by sctp_process_asconf(), it will not be safe.

so add a code in sctp_verify_asconf() to check the address parameter is in
the beginning, or return false to send abort.

note that this can also detect multiple address parameters, and reject it.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ACPI 6.0 NFIT Memory Device State Flags in Table 5-129 defines
NVDIMM status as follows.  These bits indicate multiple info,
such as failures, pending event, and capability.

  Bit [0] set to 1 to indicate that the previous SAVE to the
  Memory Device failed.
  Bit [1] set to 1 to indicate that the last RESTORE from the
  Memory Device failed.
  Bit [2] set to 1 to indicate that platform flush of data to
  Memory Device failed. As a result, the restored data content
  may be inconsistent even if SAVE and RESTORE do not indicate
  failure.
  Bit [3] set to 1 to indicate that the Memory Device is observed
  to be not armed prior to OSPM hand off. A Memory Device is
  considered armed if it is able to accept persistent writes.
  Bit [4] set to 1 to indicate that the Memory Device observed
  SMART and health events prior to OSPM handoff.

/sys/bus/nd/devices/nmemX/nfit/flags shows this flags info.
The output strings associated with the bits are "save", "restore",
"smart", etc., which can be confusing as they may be interpreted
as positive status, i.e. save succeeded.

Change also the dev_info() message in acpi_nfit_register_dimms()
to be consistent with the sysfs flags strings.
Reported-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
[ross: rename 'not_arm' to 'not_armed']
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
[djbw: defer adding bit5, HEALTH_ENABLED, for now]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Some of the stats handling code differs based on SR-IOV support,
and SRIOV support is only available if full-featured firmware is
used.
Do not use vadaptor stats if firmware mode is not set to
full-featured.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The fixed link values parsed from the device tree are stored in
the struct fixed_phy member status. The struct phy_device members
speed, duplex were not updated.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull amr64 kvm fix from Will Deacon:
 "We've uncovered a nasty bug in the arm64 KVM code which allows a badly
  behaved 32-bit guest to bring down the host.  The fix is simple (it's
  what I believe we call a "brown paper bag" bug) and I don't think it
  makes sense to sit on this, particularly as Russell ended up
  triggering this rather than just somebody noticing a potential problem
  by inspection.

  Usually arm64 KVM changes would go via Paolo's tree, but he's on
  holiday at the moment and the deal is that anything urgent gets
  shuffled via the arch trees, so here it is.

  Summary:

  Fix arm64 KVM issue when injecting an abort into a 32-bit guest, which
  would lead to an illegal exception return at EL2 and a subsequent host
  crash"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: KVM: Fix host crash when injecting a fault into a 32bit guest

When injecting a fault into a misbehaving 32bit guest, it seems
rather idiotic to also inject a 64bit fault that is only going
to corrupt the guest state. This leads to a situation where we
perform an illegal exception return at EL2 causing the host
to crash instead of killing the guest.

Just fix the stupid bug that has been there from day 1.

Cc: <stable@vger.kernel.org>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Pull block fixes from Jens Axboe:
 "Two fixes in this pull request:

   - The writeback regression fix from Tejun, which has been weeks in
     the making.  This fixes a case where we would sometimes not issue
     writeback when we should have.

   - An older fix for a memory corruption issue in mtip32xx.  It was
     deferred since we wanted a better fix for this (driver should not
     have to handle that case), but given the timing, it's better to put
     the simple fix in for 4.2 release"

* 'for-linus' of git://git.kernel.dk/linux-block:
  mtip32x: fix regression introduced by blk-mq per-hctx flush
  writeback: sync_inodes_sb() must write out I_DIRTY_TIME inodes and always call wait_sb_inodes()

The Crucial M500 is known to have issues with queued TRIM commands, the
factory recertified SSDs use a different model number naming convention
which causes them to get ignored by the blacklist.

The new naming convention boils down to: s/Crucial_/FC/
Signed-off-by: Guillermo A. Amaral <g@maral.me>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

Since commit 1851617c ("PCI/MSI: Disable MSI at enumeration even if
kernel doesn't support MSI"), the setup of dev->msi_cap/msix_cap and the
disable of MSI/MSI-X interrupts isn't being done at PCI probe time, as
the logic responsible for this was moved in the aforementioned commit
from pci_device_add() to pci_setup_device(). The latter function is not
reachable on PowerPC pseries platform during Open Firmware PCI probing
time.

This exhibits as drivers not being able to enable MSI, eg:

  bnx2x 0000:01:00.0: no msix capability found

This patch calls pci_msi_setup_pci_dev() explicitly to disable MSI/MSI-X
during PCI probe time on pSeries platform.

Fixes: 1851617c ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
[mpe: Flesh out change log and clarify comment]
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Commit 1851617c ("PCI/MSI: Disable MSI at enumeration even if kernel
doesn't support MSI") changed the location of the code that initialises
dev->msi_cap/msix_cap and then disables MSI/MSI-X interrupts at PCI
probe time in devices that have this flag set. It moved the code from
pci_msi_init_pci_dev() to a new function named pci_msi_setup_pci_dev(),
called by pci_setup_device().

The pseries PCI probing code does not call pci_setup_device(), so since
the aforementioned commit the function pci_msi_setup_pci_dev() is not
called and MSI/MSI-X interrupts are left enabled. Additionally because
dev->msi_cap/msix_cap are not initialised no driver can ever enable
MSI/MSI-X.

To fix this, the pseries PCI probe should manually call
pci_msi_setup_pci_dev(), so this patch makes it non-static.

Fixes: 1851617c ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
[mpe: Update change log to mention dev->msi_cap/msix_cap]
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

It is needed to check EVENT_NO_RUNTIME_PM bit of dev->flags in
usbnet_stop(), but its value should be read before it is cleared
when dev->flags is set to 0.

The problem was spotted and the fix was provided by
Oliver Neukum <oneukum@suse.de>.
Signed-off-by: Eugene Shatokhin <eugene.shatokhin@rosalab.ru>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull LSM regression fix from James Morris.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  LSM: restore certain default error codes

Pull nvdimm fix from Dan Williams:
 "A single fix for status register read size in the nd_blk driver.

  The effect of getting the width of this register read wrong is that
  all I/O fails when the read returns non-zero.  Given the availability
  of ACPI 6 NFIT enabled platforms, this could reasonably wait to come
  in during the 4.3 merge window with a tag for 4.2-stable.  Otherwise,
  this makes the 4.2 kernel fully functional with devices that conform
  to the mmio-block-apertures defined in the ACPI 6 NFIT (NVDIMM
  Firmware Interface Table)"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  nfit, nd_blk: BLK status register is only 32 bits

[ 1065.801569] Internal error: Oops: 96000006 [#1] SMP
...
[ 1065.866655] Hardware name: AppliedMicro Mustang/Mustang, BIOS 1.1.0 Apr 22 2015
[ 1065.873937] Workqueue: events_power_efficient phy_state_machine
[ 1065.879837] task: fffffe01de105e80 ti: fffffe00bcf18000 task.ti: fffffe00bcf18000
[ 1065.887288] PC is at linkwatch_fire_event+0xac/0xc0
[ 1065.892141] LR is at linkwatch_fire_event+0xa0/0xc0
[ 1065.896995] pc : [<fffffe000060284c>] lr : [<fffffe0000602840>] pstate: 200001c5
[ 1065.904356] sp : fffffe00bcf1bd00
...
[ 1066.196813] Call Trace:
[ 1066.199248] [<fffffe000060284c>] linkwatch_fire_event+0xac/0xc0
[ 1066.205140] [<fffffe000061167c>] netif_carrier_off+0x54/0x64
[ 1066.210773] [<fffffe00004f1654>] phy_state_machine+0x120/0x3bc
[ 1066.216578] [<fffffe00000d8d10>] process_one_work+0x15c/0x3a8
[ 1066.222296] [<fffffe00000d9090>] worker_thread+0x134/0x470
[ 1066.227757] [<fffffe00000df014>] kthread+0xe0/0xf8
[ 1066.232525] Code: 97f65ee9 f9420660 d538d082 8b000042 (885f7c40)

The fix is to call phy_disconnect() from xgene_enet_mdio_remove,
which in turn call cancel_delayed_work_sync().
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 1e052be6 ("net_sched: destroy proto tp when all filters are gone")
I added a check in u32_destroy() to see if all real filters are gone
for each tp, however, that is only done for root_ht, same is needed
for others.

This can be reproduced by the following tc commands:

tc filter add dev eth0 parent 1:0 prio 5 handle 15: protocol ip u32 divisor 256
tc filter add dev eth0 protocol ip parent 1: prio 5 handle 15:2:2 u32
ht 15:2: match ip src 10.0.0.2 flowid 1:10
tc filter add dev eth0 protocol ip parent 1: prio 5 handle 15:2:3 u32
ht 15:2: match ip src 10.0.0.3 flowid 1:10

Fixes: 1e052be6 ("net_sched: destroy proto tp when all filters are gone")
Reported-by: Akshat Kakkar <akshat.1984@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While in most cases commit b1d9e6b0 ("LSM: Switch to lists of hooks")
retained previous error returns, in three cases it altered them without
any explanation in the commit message. Restore all of them - in the
security_old_inode_init_security() case this led to reiserfs using
uninitialized data, sooner or later crashing the system (the only other
user of this function - ocfs2 - was unaffected afaict, since it passes
pre-initialized structures).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>

Only read 32 bits for the BLK status register in read_blk_stat().

The format and size of this register is defined in the
"NVDIMM Driver Writer's guide":

http://pmem.io/documents/NVDIMM_Driver_Writers_Guide.pdfSigned-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Tested-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Rather than re-initialising the entire completion on every mdio access,
use reinit_completion() which only resets the completion count.  This
avoids possible reinitialisation of the contained spinlock and waitqueue
while they may be in use (eg, mid-completion.)

Such an event could occur if there's a long delay in interrupt handling
causing the mdio accessor to time out, then a second access comes in
while the interrupt handler on a different CPU has called complete().
Another scenario where this has been observed is while locking has
been missing at the phy layer, allowing concurrent attempts to access
the MDIO bus.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The phy layer is missing locking for the above two functions - it
has been observed that two threads (userspace and the phy worker
thread) can race, entering the bus ->write or ->read functions
simultaneously.

This causes the FEC driver to initialise a completion while another
thread is waiting on it or while the interrupt is calling complete()
on it, which causes spinlock unlock-without-lock, spinlock lockups,
and completion timeouts.

Fixes: a59a4d19 ("phy: add the EEE support and the way to access to the MMD registers.")
Fixes: 0c1d77df ("net: libphy: Add phy specific function to access mmd phy registers")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>