The handler function may be called from the point it is registered.
Since the handler inspects IRQ numbers, we must set them up before
registration.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix the return value for the successful case.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The wl1271's irq line is completely controlled by the 1271 device, and
the host does not not need to pull it up.

While there's no functional effect, letting the host pull this line up is
just redundant, and wastes power.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

request_mem_region() error exit will leak ioremapped memory. Fix this
by moving the ioremap() after request_mem_region(), which is the proper
order to do this anyway.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adapts the register offsets used to read the CPU DIE ID registers
when run on 44XX so they match what is in the OMAP4430 Reference Manual
page 269
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove duplicate mux modes to make the binary smaller:

text    data     bss     dec     hex filename
9378   24472       0   33850    843a mux44xx.o
9378   19104       0   28482    6f42 mux44xx.o

Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently IOVMM driver sets IOVMF_DA_FIXED/IOVMF_DA_ANON flags according
to input 'da' address when mapping memory:
da == 0: IOVMF_DA_ANON
da != 0: IOVMF_DA_FIXED

It prevents IOMMU to map first page with fixed 'da'. To avoid such
issue, IOVMM will not automatically set IOVMF_DA_FIXED. It should now
come from the user throught 'flags' parameter when mapping memory.
As IOVMF_DA_ANON and IOVMF_DA_FIXED are mutually exclusive, IOVMF_DA_ANON
can be removed. The driver will now check internally if IOVMF_DA_FIXED
is set or not.
Signed-off-by: David Cohen <dacohen@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

commit c7f4ab26 allowed mapping the NULL
address if da_start==0, which would then not get unmapped. Disallow
this again if IOVMF_DA_ANON is set. And spell variable 'alignment'
correctly.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix compile when CONFIG_OMAP_MUX is not selected
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use the mux framework to initialise the serial pads.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use the mux framework to initialise the serial pads.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use the mux framework to initialise the serial pads.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add macro for defining static pins in the board file.

We can now start implementing pin multiplexing in the platform init
code for devices that call omap_hwmod_mux_init. Currently that is
only implemented for serial.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently OMAP_DEVICE_PAD_IDLE flag is used to mux pins
dynamically. This can be simplified by using the enabled
state variable of each pad. This also fixes the issue of
the static pads not getting muxed after idling and
disable/enable state transitions.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This avoids going through the list unnecessarily when
idling devices for runtime PM.

Based on an earlier patch by sricharan <r.sricharan@ti.com>.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge branch 'for_2.6.39/pm-integration' of ssh://master.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-linus

Merge branch 'integration-2.6.39-for-tony' of git://git.pwsan.com/linux-integration into omap-for-linus

Conflicts:
	arch/arm/mach-omap2/pm34xx.c

The patch adds the new power management trace points for
the OMAP architecture.

The trace points are for:
- default idle handler. Since the cpuidle framework is
  instrumented in the generic way there is no need to
  add trace points in the OMAP specific cpuidle handler;
- SoC clocks changes (enable, disable, set_rate),
- power domain states: the desired target state and -if different-
  the actually hit state.

Because of the generic nature of the changes, OMAP3 and OMAP4 are supported.

Tested on OMAP3 with suspend/resume, cpuidle, basic DVFS.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

This Patch adds OPP enteries for IVA  in OMAP4 OPP Table

Tested on OMAP4430 SDP Board.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Update MPU, IVA and CORE voltage Rail values obtained from
OMAP4430 Data Manual Operating Condition Addendum_v0.4.

Tested on OMAP4430 SDP Board.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Almost all OMAP4 boards support OPP 800 MHz and OPP 1 GHz.
Enable them in OPP Table. For small minority of boards which use
OMAP4430-800 MHz device OPP 1GHz is not supported,
OPP 1GHz should be disabled from board file.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Since all voltage data is now centralized in oppxxx_data.c, we can replace
the values in the opp table with the macros used for voltage values.

This will avoid opp table and voltage layer having conflicting values.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Conflicts:
	arch/arm/mach-omap2/omap_hwmod_3xxx_data.c

Conflicts:
	arch/arm/mach-omap2/omap_hwmod_2430_data.c
	arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
	arch/arm/plat-omap/include/plat/omap_hwmod.h

Merge remote branches 'remotes/origin/pwrdm_clkdm_b_2.6.39', 'remotes/origin/pwrdm_add_can_lose_context_fns_2.6.39', 'remotes/origin/omap_device_a_2.6.39', 'remotes/origin/mmc_a_2.6.39', 'remotes/origin/hwmod_b_2.6.39', 'remotes/origin/dmtimer_a_2.6.39', 'remotes/origin/pwrdm_clkdm_a_2.6.39', 'remotes/origin/clkdm_statdep_omap4_2.6.39', 'remotes/origin/clk_a_2.6.39', 'remotes/origin/clk_autoidle_a_2.6.39', 'remotes/origin/clk_autoidle_b_2.6.39', 'remotes/origin/clk_b_2.6.39', 'remotes/origin/clk_clkdm_a_2.6.39', 'remotes/origin/misc_a_2.6.39', 'remotes/origin/for_2.6.39/omap3_hwmod_data' and 'remotes/origin/wdtimer_a_2.6.39' into tmp-integration-2.6.39-20110310-024

The HW superwised smart idle for wdtimer in OMAP3 prevents
CORE power domain idle transitions. Disable it by swithing
to SW supervised transitions.

This could be a hardware bug in the OMAP3 wdtimer2 block.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>

The omap_wdt should only be in full active state when the
registers are being accessed. Otherwise the device can be
on lower power mode.

This patch is based on a patch created by Kalle Jokiniemi:
https://patchwork.kernel.org/patch/618231/
which is itself based on a patch created by Atal
Shargorodsky: http://lkml.org/lkml/2009/3/10/266.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Tested-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Kevin Hilman <khilman@ti.com>

This is a first pass at reorganizing mach-omap2/voltage.c:

- Separate almost all of the data from the code of mach-omap2/voltage.c.
  The code remains in mach-omap2/voltage.c.  The data goes into one
  of several places, depending on what type of data it is:

  - Silicon process/validation data: mach-omap2/opp*_data.c
  - VC (Voltage Controller) data: mach-omap2/vc*_data.c
  - VP (Voltage Processor) data: mach-omap2/vp*_data.c
  - Voltage domain data: mach-omap2/voltagedomains*_data.c

  The ultimate goal is for all this data to be autogenerated, the same
  way we autogenerate the rest of our data.

- Separate VC and VP common data from VDD-specific VC and VP data.

- Separate common voltage.c code from SoC-specific code; reuse common code.

- Reorganize structures to avoid unnecessary memory loss due to unpacked
  fields.

There is much left to be done.  VC code and VP code should be separated out
into vc*.c and vp*.c files.  Many fields in the existing structures are
superfluous, and should be removed.  Some code in voltage.c seems to be
duplicated; that code should be moved into functions of its own.  Proper
voltage domain code should be created, as was done with the powerdomain
and clockdomains, and powerdomains should reference voltagedomains.

Thanks to Shweta Gulati <shweta.gulati@ti.com> for comments.  Thanks
to Rajendra Nayak <rnayak@ti.com> for finding and fixing some bugs
that prevented OMAP4 from booting:

   https://patchwork.kernel.org/patch/587311/

His patch has been folded into this one to avoid breaking OMAP4
between patches.  Thanks also to Kevin Hilman <khilman@ti.com> for
finding and fixing a compile problem when !CONFIG_PM:

   http://www.spinics.net/lists/arm-kernel/msg118067.html

His patch has also been folded into this one to avoid breaking
!CONFIG_PM builds.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Shweta Gulati <shweta.gulati@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Kevin Hilman <khilman@ti.com>

Merge branch 'for_2.6.39/pm-misc' of ssh://master.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-linus

On the newer ARM processors like CortexA8, CortexA9, the caches can be
speculatively loaded while they are getting flushed.

Clear the SCTLR C bit to prevent further data cache allocation as
part of cache clean routine
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

The current code saves few un-necessary registers which are read-only or
write-only, unused CP15 registers.

Remove them and keep only necessary CP15 registers part of
low power context save/restore.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

When L1 cache is suppose to be lost, it needs to be cleaned before
entrering to the low power mode.

While at this, also fix few comments and remove un-necessary
clean_l2 lable.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Add necessary barriers after enabling MMU. Also use the sane way to
load pc and jump to it instead of executing ldma first up.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

On ARMv7 dsb, dmb instructions are supported and can be used directly
instead of their cp15 equivalnet. Also remove the opcodes for smc
and use the available instruction directly in OMAP3 low power asm code
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

There should be no reason to call h4_init_flash this
early. It causes problems as things are not yet initialized.
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This saves some power. OMAP4 version should check for GPT module ID, as
autoidle is only supported on a subset of these.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Add a new clockdomain flag, CLKDM_NO_AUTODEPS, which, when marked on a
clockdomain, will prevent "autodeps" from being associated with the
clockdomain.  ("Autodeps" are sleep dependencies and wakeup
dependencies from/to processor modules that are automatically added to
a clockdomain when it is in hardware-supervised idle mode.  They are
deprecated -- a relic from the old CDP trees -- but are still in use
for OMAP3.)

Also, prevent the hwmod code from adding or removing initiator
dependencies for clockdomains with this flag set.

This patch should allow others to test which clockdomains actually
still need autodeps.

Thanks to Kevin Hilman <khilman@ti.com> for noting that the original
version should also modify the hwmod code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>

Create a new API that forms a wrapper to _set_module_autoidle()
to modify the AUTOIDLE bit.

This API is intended to be used by drivers that requires direct
manipulation of the AUTOIDLE bits in SYSCONFIG register.
McBSP driver requires autoidle bit to be enabled/disabled while
using sidetone feature.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: restrict the hwmod states that the autoidle bit can be changed
 in; changed function name; dropped "int" from "unsigned int long"]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Some boards can't tolerate IP blocks being reset when they are initialized.
Michael Büsch cites a case with the Nokia N810:

    http://www.spinics.net/lists/linux-omap/msg47277.html

To allow such boards to continue working normally, allow board file
maintainers to mark IP blocks to prevent them from being reset upon
init.  This is done via a hwmod function, omap_hwmod_no_setup_reset().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Michael Buesch <mb@bu3sch.de>