Update calculation for the R-Car Gen3 and RZ/G2 SoCs which have a
thermal IP block controlled by this driver. That is the:

* R-Car D3 (r8a77995)
* R-Car E2 (r8a77990)
* R-Car V3M (r8a77970)
* RZ/G2E (r8a774c0)

The calculation update is as documented in the R-Car Gen3 User's Manual,
v1.50 Nov 2018:

- When CTEMP is less than 24
   T = CTEMP[5:0] * 5.5 - 72
- When CTEMP is equal to/greater than 24
   T = CTEMP[5:0] * 5 - 60

This was inspired by a patch in the BSP by Van Do <van.do.xw@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

The CPU load values passed to the thermal_power_cpu_get_power
tracepoint are zero for all CPUs, unless, unless the
thermal_power_cpu_limit tracepoint is enabled too:

  irq/41-rockchip-98    [000] ....   290.972410: thermal_power_cpu_get_power:
  cpus=0000000f freq=1800000 load={{0x0,0x0,0x0,0x0}} dynamic_power=4815

vs

  irq/41-rockchip-96    [000] ....    95.773585: thermal_power_cpu_get_power:
  cpus=0000000f freq=1800000 load={{0x56,0x64,0x64,0x5e}} dynamic_power=4959
  irq/41-rockchip-96    [000] ....    95.773596: thermal_power_cpu_limit:
  cpus=0000000f freq=408000 cdev_state=10 power=416

There seems to be no good reason for omitting the CPU load information
depending on another tracepoint. My guess is that the intention was to
check whether thermal_power_cpu_get_power is (still) enabled, however
'load_cpu != NULL' already indicates that it was at least enabled when
cpufreq_get_requested_power() was entered, there seems little gain
from omitting the assignment if the tracepoint was just disabled, so
just remove the check.

Fixes: 6828a471 ("thermal: add trace events to the power allocator governor")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Javi Merino <javi.merino@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

PX30 SOC has two Temperature Sensors for CPU and GPU.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Add a new compatible for thermal founding on PX30 SoCs.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Explicitly use the pinctrl to set/unset the right mode
instead of relying on the pinctrl init mode.
And it requires setting the tshut polarity before select pinctrl.

When the temperature sensor mode is set to 0, it will automatically
reset the board via the Clock-Reset-Unit (CRU) if the over temperature
threshold is reached. However, when the pinctrl initializes, it does a
transition to "otp_out" which may lead the SoC restart all the time.

"otp_out" IO may be connected to the RESET circuit on the hardware.
If the IO is in the wrong state, it will trigger RESET.
(similar to the effect of pressing the RESET button)
which will cause the soc to restart all the time.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Unlike DT framework, thermal-zones and its parameters can't be parsed
using ACPI framework. So that ACPI support is removed in this driver.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reported-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

The devres.o gets linked if HAS_IOMEM is present so on ARCH=um
allyesconfig (COMPILE_TEST) failed on many files with:

drivers/thermal/thermal_mmio.o:
In function 'thermal_mmio_probe':thermal_mmio.c:(.text+0xe1):
undefined reference to `devm_ioremap_resource'

The users of devm_ioremap_resource() which are compile-testable
should depend on HAS_IOMEM.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

The structure cpufreq_cooling_device provides a backpointer to the thermal
device but this one is used for a trace and to unregister. For the trace,
we don't really need this field and the unregister function as the same
pointer passed as parameter. Remove it.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

For license auditing purpose, let's add the SPDX tag.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

The copyright format does not conform to the format requested by
Linaro: https://wiki.linaro.org/Copyright

Fix it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

When the static power computation was removed, the test with the power
being negative was not removed. However, the substraction which was
responsible of the negative value was removed and the variable is now
an u32. A double reason to remove the test which does not make sense.

Fixes: 84fe2cab ("cpu_cooling: Drop static-power related stuff")
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Currently IRQ remains enabled after .remove, later if device is probed,
IRQ is requested before .thermal_init, this may cause IRQ function be
called before device is initialized.

this patch disables interrupt in .remove, to ensure irq function
only be called after device is fully initialized.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Currently IRQF_SHARED type interrupt line is allocated, but it
is not appropriate, as the interrupt line isn't shared between
different devices, instead IRQF_ONESHOT is the proper type.

By changing interrupt type to IRQF_ONESHOT, now irq handler is
no longer needed, as clear of interrupt status can be done in
threaded interrupt context.

Because IRQF_ONESHOT type interrupt line is kept disabled until
the threaded handler has been run, so there is no need to protect
read/write of REG_GEN3_IRQSTR with lock.

Fixes: 7d4b2697 ("enable hardware interrupts for trip points")
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

thermal_of_cooling_device_register() and thermal_cooling_device_register()
are typically called from driver probe functions, and
thermal_cooling_device_unregister() is called from remove functions. This
makes both a perfect candidate for device managed functions.

Introduce devm_thermal_of_cooling_device_register(). This function can
also be used to replace thermal_cooling_device_register() by passing a NULL
pointer as device node. The new function requires both struct device *
and struct device_node * as parameters since the struct device_node *
parameter is not always identical to dev->of_node.

Don't introduce a device managed remove function since it is not needed
at this point.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Update binding description making lookup-table optional.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Certain ADC channels, such as the xilinx-ams temperature channels, give
milliCelcius already when read with iio_read_channel_processed.

Rather than having to provide a 1:1 dummy lookup table, simply allow to
bypass the mechanism.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

It's impossible to use this driver outside of Device Tree, so if the
probe function is called, the dev.of_node is guaranteed to not be NULL
and guarding against that is pointless. Drop it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: linux-imx@nxp.com
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

This is a generic thermal driver for simple MMIO sensors, of which
amazon,al-thermal is one.

This device uses a single MMIO transaction to read the temperature and
report it to the thermal subsystem.
Signed-off-by: Talel Shenhar <talel@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Add thermal binding documentation for Amazon's Annapurna Labs Thermal
Sensor.
Signed-off-by: Talel Shenhar <talel@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Fix setting value for IRQCTL register. We are setting the last 6 bits
of (IRQCTL) to be 1 (0x3f), this is only suitable for H3ES1.*, according
to Hardware manual values 1 are "setting prohibited" for Gen3.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

This will allow calibration routines to correctly include the constants
from anywhere and allow more code sharing.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

qcs404 has a single TSENS IP block with 10 sensors. It uses version 1.4
of the TSENS IP, functionality for which is encapsulated inside the
qcom,tsens-v1 compatible.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

qcs404 uses v1 of the TSENS IP block. Create a fallback DT property
"qcom,tsens-v1" to gather common code
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

get_temp() learns to return temperature regardless of whether it is
returned as ADC code or direct temperature.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Just rename the function and move it to allow code sharing with future
versions of TSENS IP
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

The current implementation is based on an algorithm published in the
docs. Instead of reading the temperature thrice w/o any explanation,
improve the algorithm.

This will become the basis for a common get_temp routine in the future.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

The IP can support 'm' sensors while the platform can enable 'n' sensors
of the 'm' where n <= m.

Track maximum sensors supported by the IP so that we can correctly track
what subset of the sensors are supported on the platform.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

The IDs cannot be negative, fix the data type.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

is_sensor_enabled() checks if the sensors are enabled on this platform.
It is possible that the SoC might choose not to enable all the sensors
that the IP block is capable of supporting.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

We print a calibration failure message on -EPROBE_DEFER from
nvmem/qfprom as follows:
[    3.003090] qcom-tsens 4a9000.thermal-sensor: version: 1.4
[    3.005376] qcom-tsens 4a9000.thermal-sensor: tsens calibration failed
[    3.113248] qcom-tsens 4a9000.thermal-sensor: version: 1.4

This confuses people when, in fact, calibration succeeds later when
nvmem/qfprom device is available. Don't print this message on a
-EPROBE_DEFER.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Code cleanup making it easier to read
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

As we add support for newer versions of the TSENS IP, the current
approach isn't scaling because registers and bitfields get moved around,
requiring platform-specific hacks in the code. By moving to regmap, we
can hide the register level differences away from the code.

Define a common set of registers and bit-fields that we care about
across the various tsens IP versions.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

8974 and 8916 have the same version of the TSENS IP. Merge the files to
allow for better code reuse.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Some #defines in tsens-v_0_1.c clash with those in tsens-8974.c. Prefix
them with 8916 to avoid the clash so we can merge the two files.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

8916 and 8974 use v0.1.0 of the TSENS IP. Rename tsens-8916 to prepare
it for merging with tsens-8974 in a later commit.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

check_patch complains a lot as follows:

WARNING: function definition argument 'struct tsens_priv *' should also have an identifier name
+       int (*init)(struct tsens_priv *);

Fix it.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

tsens_get_temp() uses the name 'data' for the void pointer, use the same
in tsens_get_trend() for consistency.

Remove a stray space while we're at it.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

tmdev seems to imply that this is a device pointer when in fact it is
just private platform data for each tsens device. Rename it to priv
improve code readability.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Rename to tsens_priv to denote that it is private data for each tsens
instance.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Rename to tsens_plat_data to denote that it is platform-data passed in
at compile-time.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>