The hwmod code unconditionally calls _omap4_disable_module() on all
SoCs when a module doesn't enable correctly.  This "worked" due to the
weak function omap4_cminst_wait_module_idle() in
arch/arm/mach-omap2/prcm.c, which was a no-op.  But now those weak
functions are going away - they should not be used.  So this patch
will now call the SoC-specific disable_module code, assuming it
exists.

Needs to be done before the weak function is removed, otherwise AM33xx
will crash early in boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Consolidate all of the copies of MAX_MODULE_HARDRESET_WAIT and
MAX_MODULE_SOFTRESET_WAIT into one place, arch/arm/mach-omap2/prm.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Split omap2_set_globals_prcm() into PRM, CM, and PRCM_MPU variants, since
these are all separate IP blocks.  This should make it easier to move the
PRM, CM, PRCM_MPU code into drivers/ in future patchsets.

At this point arch/arm/plat-omap/include/plat/prcm.h is empty; a
subsequent patch will remove it, and remove the #include from all the
files that #include it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Now that all users of mach-omap2/omap2_cm_wait_idlest() have been removed,
delete the function and its supporting macros and prototypes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Convert the OMAP clock code's _omap2_module_wait_ready() to use
SoC-independent CM functions that are provided by the CM code, rather
than using a deprecated function from mach-omap2/prcm.c.

This facilitates the future conversion of the CM code to a driver, and
also removes a mach-omap2/prcm.c user.  mach-omap2/prcm.c will be removed
by a subsequent patch.

Some modules have IDLEST registers that aren't in the CM module, such
as the AM3517 IDLEST bits.  So we also need a fallback function for
these non-CM odd cases.  Create a temporary one in mach-omap2/clock.c,
intended to exist until the SCM drivers are ready.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Convert the OMAP2xxx APLL code to use omap2_cm_wait_module_ready(),
and move the low-level CM register manipulation functions to
mach-omap2/cm2xxx.c.  The objectives here are to remove the dependency
on the deprecated omap2_cm_wait_idlest() function in
mach-omap2/prcm.c, so that code can be removed later; and move
low-level register accesses to the CM IP block to the CM code, which
will soon be moved into drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Modify the board files to use the SoC-specific system restart
functions.  At this point it's possible to remove omap_prcm_restart()
from mach-omap2/prcm.c.

While removing the prototypes for the now-unused restart functions, clean
up a few more obsolete prototypes in mach-omap2/clock.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Split omap_prcm_restart() from mach-omap2/prcm.c into SoC-specific
variants.  These functions need to be able to save the reboot reason
into the scratchpad RAM.  This implies a dependency on both the PRM
and SCM IP blocks, so they've been moved into their own file.  This
will eventually call functions in the PRM and SCM drivers, once those
are created.

Vaibhav Hiremath <hvaibhav@ti.com> identified an unused prototype in
the first version of this patch - now removed.  Tony Lindgren
<tony@atomide.com> noted a compile problem with some RMK Kconfigs;
resolved in this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

Collect all of the virt_prcm_set-specific clocktype code into
mach-omap2/clkt2xxx_virt_prcm_set.c.  Remove its dependency on the
'sclk' and 'vclk' global variables.  Those variables will be removed
by subsequent patches.

This is part of the process of cleaning up the OMAP2xxx clock code
and preparing for the removal of the omap_prcm_restart() function.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Remove the global 'dclk' variable, instead replacing it with a
variable local to the dpllcore clock type C file.  This removes some
of the special-case code surrounding the OMAP2xxx clock init.

This patch is a prerequisite for the removal of the
omap_prcm_restart() code from arch/arm/mach-omap2/prcm.c.  It also
cleans up some special-case OMAP2xxx clock code in the process.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Add SoC reset functions into the PRM code.  These functions are based
on code from mach-omap2/prcm.c.  They reset the SoC using the CORE DPLL
reset method (as opposed to one of the other two or three chip reset
methods).

Adding them here will facilitate their removal from
arch/arm/mach-omap2/prcm.c.  (prcm.c is deprecated.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Get rid of the mach-omap2/common.c globals by moving the global
initialization for IP block addresses that must occur early into
mach-omap2/io.c.  In the process, remove the *_map_common_io*() and
SoC-specific *set_globals* functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

omap_prcm_get_reset_sources() is now unused; so, remove it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Previously the OMAP watchdog driver used a non-standard way to report
the chip reset source via the GETBOOTSTATUS ioctl.  This patch
converts the driver to use the standard WDIOF_* flags for this
purpose.

This patch may break existing userspace code that uses the existing
non-standard data format returned by the OMAP watchdog driver's
GETBOOTSTATUS ioctl.  To fetch detailed reset source information,
userspace code will need to retrieve it directly from the CGRM or PRM
drivers when those are completed.

Previously, to fetch the reset source, the driver either read a
register outside the watchdog IP block (OMAP1), or called a function
exported directly from arch/arm/mach-omap2.  Both approaches are
broken.  This patch also converts the driver to use a platform_data
function pointer.  This approach is temporary, and is due to the lack
of drivers for the OMAP16xx+ Clock Generation and Reset Management IP
block and the OMAP2+ Power and Reset Management IP block.  Once
drivers are available for those IP blocks, the watchdog driver can be
converted to call exported functions from those drivers directly.
At that point, the platform_data function pointer can be removed.

In the short term, this patch is needed to allow the PRM code to be
removed from arch/arm/mach-omap2 (it is being moved to a driver).

This version integrates a fix from Jon Hunter <jon-hunter@ti.com>
that avoids a NULL pointer dereference in a DT-only boot, and integrates
a patch commit message fix from Felipe Balbi <balbi@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
[paul@pwsan.com: integrated pdata fix from Jon Hunter]
Cc: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: integrated changelog fix from Felipe Balbi]
Cc: Felipe Balbi <balbi@ti.com>

The OMAP watchdog timer driver directly calls a function exported by
code in arch/arm/mach-omap2.  This is not good; it tightly couples
this driver to the mach-omap2 integration code.  Instead, add a
temporary platform_data function pointer to abstract this function
call.  A subsequent patch will convert the watchdog driver to use this
function pointer.

This patch also moves the device creation code out of
arch/arm/mach-omap2/devices.c and into arch/arm/mach-omap2/wd_timer.c.
This is another step towards the removal of
arch/arm/mach-omap2/devices.c.

Cc: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
[paul@pwsan.com: skip wd_timer device creation when DT blob is present]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

An older version of the patch "ARM: OMAP1: create read_reset_sources()
function (for initial use by watchdog)" was sent upstream, which used
the wrong return type for the omap1_get_reset_sources() function.
Fix it to return a u32, which is what the WDTIMER platform_data
function pointer read_reset_sources() expects.
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Merge tag 'omap-cleanup-fixes-a-for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.8/cleanup-headers

Several fixes for build failures and sparse warnings in the
OMAP cleanup-headers branch.  Intended for 3.8 cleanup.

Basic build, boot, and PM test logs are available from here:

    http://www.pwsan.com/omap/testlogs/cleanup-headers-compile-fixes-3.8/20121026132711/

Due to underlying problems in v3.7-rc2, several tests fail.  These
failures are unrelated to these patches.

Commit 4c98dc6b ("ARM: OMAP: Make
plat/fpga.h local to arch/arm/plat-omap") results in a new warning from
sparse:

arch/arm/mach-omap1/fpga.c:147:6: warning: symbol 'omap1510_fpga_init_irq' was not declared. Should it be static?

Fix by adding a missing include.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>

Commit 25c7d49e ("ARM: OMAP: Make
omap_device local to mach-omap2") broke an OMAP5912-only build here:

arch/arm/mach-omap1/pm_bus.c: In function 'omap1_pm_runtime_init':
arch/arm/mach-omap1/pm_bus.c:69:2: error: implicit declaration of function
'cpu_class_is_omap1'
make[1]: *** [arch/arm/mach-omap1/pm_bus.o] Error 1

Fix by adding a missing include.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>

Commit b7754452 ("mtd: onenand: omap:
use pdata info instead of cpu_is") broke an OMAP3+4 build and an N800
multi-OMAP2xxx build here:

drivers/built-in.o: In function `omap2_onenand_probe':
drivers/mtd/onenand/omap2.c:742: undefined reference to `omap2_onenand_read_bufferram'
drivers/mtd/onenand/omap2.c:743: undefined reference to `omap2_onenand_write_bufferram'
drivers/mtd/onenand/omap2.c:742: undefined reference to `omap2_onenand_read_bufferram'
drivers/mtd/onenand/omap2.c:743: undefined reference to `omap2_onenand_write_bufferram'

...

drivers/built-in.o: In function `omap2_onenand_probe':
drivers/mtd/onenand/omap2.c:788: undefined reference to `omap3_onenand_read_bufferram'
drivers/mtd/onenand/omap2.c:788: undefined reference to `omap3_onenand_write_bufferram'

Fix by declaring static functions for the missing symbols, rather than
just prototypes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Afzal Mohammed <afzal@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

Conflicts:
	arch/arm/mach-omap2/board-h4.c
	arch/arm/mach-omap2/board-n8x0.c

Merge tag 'omap-cleanup-a-for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.8/cleanup-prcm

The first set of OMAP PRM/CM-related cleanup patches for 3.8.
Prepares for the future move of the PRM/CM code to drivers/.  Also
includes some prcm.[ch] cleanup patches from the WDTIMER cleanup
series that don't need external acks.

Basic test logs for this branch on top of v3.7-rc2 are here:

http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121021123719/

But due to the number of unrelated regressions present in v3.7-rc[12],
it's not particularly usable as a testing base.  With reverts, fixes,
and workarounds applied as documented in:

http://www.pwsan.com/omap/testlogs/test_v3.7-rc2/20121020134755/README.txt

the following test logs were obtained:

http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121020231757/

which indicate that the series tests cleanly.

Conflicts:
	arch/arm/mach-omap2/Makefile
	arch/arm/mach-omap2/clockdomain2xxx_3xxx.c
	arch/arm/mach-omap2/pm24xx.c

Conflicts:
	arch/arm/mach-omap1/clock.c
	arch/arm/mach-omap2/board-2430sdp.c
	arch/arm/mach-omap2/board-4430sdp.c
	arch/arm/mach-omap2/board-cm-t35.c
	arch/arm/mach-omap2/board-igep0020.c
	arch/arm/mach-omap2/board-ldp.c
	arch/arm/mach-omap2/board-omap3beagle.c
	arch/arm/mach-omap2/board-omap3logic.c
	arch/arm/mach-omap2/board-omap4panda.c
	arch/arm/mach-omap2/board-overo.c
	arch/arm/mach-omap2/board-rm680.c
	arch/arm/mach-omap2/board-rx51.c
	arch/arm/mach-omap2/twl-common.c
	arch/arm/mach-omap2/usb-host.c
	arch/arm/mach-omap2/usb-musb.c

In order to make single zImage work for ARM architecture,
we need to make sure we don't depend on private headers.

Move USB platform_data to <linux/platform_data/omap-usb.h>
and add a minimal drivers/mfd/usb-omap.h.

Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Partha Basak <parthab@india.ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated for local mfd/usb-omap.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>

Let's move what we can from plat/usb.h to the local usb.h
for ARM common zImage support.

This is needed so we can remove plat/usb.h for ARM common
zImage support.

Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Partha Basak <parthab@india.ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

For omap1, we'll keep mach/serial.h around for 8250.c hardware
workarounds. For omap2+, we no longer need mach/serial.h and
can make it local to mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>

This allows us to eventually move omap2+ to generic
debug code that's configured in Kconfig for the port.
Signed-off-by: Tony Lindgren <tony@atomide.com>

This is the first set of omap cleanup patches for v3.8 merge
window to remove most of the remaining plat includes to get us
closer to ARM common zImage support.

To avoid a huge amount of trivial merge conflicts with includes,
this branch is based on several small topic branches coordinated
with the driver subsystem maintainers. These branches are based on
v3.7-rc1 and can also be merged into the related driver subsystem
branches as needed:

omap-for-v3.8/cleanup-headers-prepare   few trivial driver changes
omap-for-v3.8/cleanup-headers-dma       move of the DMA header
omap-for-v3.8/cleanup-headers-gpmc      GPMC and MTD changes
omap-for-v3.8/cleanup-headers-mmc       MMC related changes
omap-for-v3.8/cleanup-headers-dss       DSS related changes
omap-for-v3.8/cleanup-headers-asoc      ASoC related changes

Note that for the dma-omap.h, it was decided that it should be
is completed. For the related discussion, please see:

https://patchwork.kernel.org/patch/1519591/#

After these patches we still have a few plat headers remaining
that will be handled in later pull requests.

This allows us to get rid of the ifdefs in 8250.c.

Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Modify divisor to select the nearest baud rate divider rather than the
lowest. It minimizes baud rate errors especially on low UART clock
frequencies.

For example, if uartclk is 33000000 and baud is 115200 the ratio is
about 17.9 The current code selects 17 (5% error) but should select 18
(0.5% error).

This 5% error in baud rate leads to garbage on receiving end, while 0.5%
doesn't.

The issue showed up when using the stock 8250 driver for
Synopsys DW UART. This was on a FPGA with ~12MHz UART clock.
When we enabled early serial, we saw garbage which was narrowed down
to the rounding error.

So the bug had been latent and it only showed up with such low clock rates.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When a driver has the low_latency flag set and uses the schedule_flip()
function to initiate copying data to the line discipline, a workqueue is
scheduled in but never actually flushed. This is incorrect use of the
low_latency flag (driver should not support the low_latency flag, or use
the tty_flip_buffer_push() function instead). Make sure a warning is
reported to catch incorrect use of the low_latency flag.

This patch goes with: cee4ad1eSigned-off-by: Ivo Sieben <meltedpianoman@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of BUG_ON(in_interrupt()), since that doesn't check for all
the newfangled stuff like preempt.

Note that this is valid since the console_sem is essentially used like
a real mutex with only two twists:
- we allow trylock from hardirq context
- across suspend/resume we lock the logical console_lock, but drop the
  semaphore protecting the locking state.

Now that doesn't guarantee that no one is playing tricks in
single-thread atomic contexts at suspend/resume/boot time, but
- I couldn't find anything suspicious with some grepping,
- might_sleep shouldn't die,
- and I think the upside of catching more potential issues is worth
  the risk of getting a might_sleep backtrace that would have been
  save (and then dealing with that fallout).

Cc: Dave Airlie <airlied@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

So this is it. The big step why we did all the work over the past
kernel releases. Now everything is prepared, so nothing protects us
from doing that big step.

           |  |            \  \ nnnn/^l      |  |
           |  |             \  /     /       |  |
           |  '-,.__   =>    \/   ,-`    =>  |  '-,.__
           | O __.´´)        (  .`           | O __.´´)
            ~~~   ~~          ``              ~~~   ~~
The buffers are now in the tty_port structure and we can start
teaching the buffer helpers (insert char/string, flip etc.) to use
tty_port instead of tty_struct all around.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For that purpose we have to temporarily introduce a second tty back
pointer into tty_port. It is because serial layer, and maybe others,
still do not use tty_port_tty_set/get. So that we cannot set the
tty_port->tty to NULL at will now.

Yes, the fix would be to convert whole serial layer and all its users
to tty_port_tty_set/get. However we are in the process of removing the
need of tty in most of the call sites, so this would lead to a
duplicated work.

Instead we have now tty_port->itty (internal tty) which will be used
only in flush_to_ldisc. For that one it is ensured that itty is valid
wherever the work is run. IOW, the work is synchronously cancelled
before we set itty to NULL and also before hangup is processed.

After we need only tty_port and not tty_struct in most code, this
shall be changed to tty_port_tty_set/get and itty removed completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

During the move of tty buffers from tty_struct to tty_port, we will
need to switch all users of buf to tty->port->buf. There are many
functions where this is accessed directly in their code many times.
Cache the tty->buf pointer in such functions now and change only
single lines in each function in the next patch.

Not that it is convenient for the next patch, but the code is now also
more readable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

They are only TTY buffers specific. And the buffers will go to
tty_port in the next patches. So to remove the need to have both
tty_port and tty_struct at some places, let us move the flags to
tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In some funtions we need only n_tty_data, so pass it down directly in
case tty is not needed there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

atomic_write_lock is not n_tty specific, so move it up in the
tty_struct.

And since these are the last ones to move, remove also the comment
saying there are some ldisc' members. There are none now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>