Merge tag 'renesas-arm64-dt2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64

Second Round of Renesas ARM64 Based SoC DT Updates for v4.11

r8a779[56] SoCs:
* Mark EthernetAVB device node disabled in DT for r8a779[56] SoCs
  - They are enabled as appropriate in board DT files
* Link ARM GIC to clock and clock domain on r8a779[56] SoCs
* Add thermal support

r8a7795 SoC:
* Tidyup audma definition order on r8a7795 SoC
* Add missing power-domains property for SATA

r8a7795/h3ulcb board:
* Add MIX/CTU support as per support present in DT for r8a7796

* tag 'renesas-arm64-dt2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  arm64: dts: r8a7796: Mark EthernetAVB device node disabled
  arm64: dts: r8a7795: Mark EthernetAVB device node disabled
  arm64: dts: r8a7795: tidyup audma definition order
  arm64: dts: r8a7796: Link ARM GIC to clock and clock domain
  arm64: dts: r8a7795: Link ARM GIC to clock and clock domain
  arm64: dts: r8a7796: Add R-Car Gen3 thermal support
  arm64: dts: r8a7795: Add R-Car Gen3 thermal support
  arm64: dts: r8a7795: Add missing power-domains property for sata
  arm64: dts: h3ulcb: follow sound CTU/MIX supports
Signed-off-by: Olof Johansson <olof@lixom.net>

ARM64: DT: Hisilicon SoC DT updates for 4.11

- Add binding for Hi3660 SoC and HiKey960 Board
- Add binding for ARM Cortex-A73
- Add dts files for HiKey960 development board

* tag 'hisi-arm64-dt-for-4.11' of git://github.com/hisilicon/linux-hisi:
  arm64: dts: Add dts files for Hisilicon Hi3660 SoC
  dt-bindings: Add a support cpu type for cortex-a73
  document: dt: add binding for Hi3660 SoC
Signed-off-by: Olof Johansson <olof@lixom.net>

For mt8173:
- set mm_sel clock to 400 MHz to support 4K HDMI
- adjust power efficiency between the little and big cores
- add a node for thermal calibration via e-fuse data

* tag 'v4.10-next-dts' of https://github.com/mbgg/linux-mediatek:
  arm64: dts: mt8173: add node for thermal calibration
  arm64: dts: mt8173: Fix cpu_thermal cooling-maps contributions
  arm64: dts: mt8173: add mmsel clocks for 4K support
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'qcom-arm64-for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt64

Qualcomm ARM64 Updates for v4.11

* Add Vol+ support for DB820C and APQ8016
* Add HDMI audio support for APQ8016
* Fix DB820C GPIO pinctrl name
* Enable WCNSS on MSM8916
* Add SCM node for MSM8996
* Use fixed XO clock on MSM8916

* tag 'qcom-arm64-for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  arm64: dts: db820c: add support to volume up key
  arm64: dts: apq8016-sbc: Limit MPP4 high state to 1.8V
  arm64: dts: apq8016-sbc: Add Volume Up key device node
  arm64: dts: apq8016-sbc: add support to hdmi audio via adv7533
  arm64: dts: db820c: fix gpio pinctrl name correctly
  ARM: dts: msm8916: Add and enable wcnss node
  arm64: dts: msm8996: Add SCM DT node
  arm64: dts: qcom: msm8916: Use fixed factor xo clock
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'uniphier-dt64-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt64

UniPhier ARM64 SoC DT updates for v4.11

- Add an SD reset controller node for LD11 SoC
- Add an eMMC controller node for LD11/LD20 SoC

* tag 'uniphier-dt64-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  arm64: dts: uniphier: add eMMC controller node for LD11/LD20
  arm64: dts: uniphier: add SD-ctrl node for LD11 SoC
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'v4.11-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64

64bit dts changes with some adjustments to the pcie controller,
usb clocks, grf phandles for the rk3399 CRUs, epd pinctrl settings,
a phandle to the rk3399 tsadc and converting boards to use the
recently introduced pin constants.

* tag 'v4.11-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  arm64: dts: rockchip: add rockchip,grf property for RK3399 PMUCRU/CRU
  arm64: dts: rockchip: add aspm-no-l0s for rk3399
  arm64: dts: rockchip: add max-link-speed for rk3399
  arm64: dts: rockchip: use pin constants to describe gpios
  arm64: dts: rockchip: add u2phy clock for ehci and ohci of rk3399
  arm64: dts: rockchip: add rk3399 eDP HPD pinctrl
  arm64: dts: rockchip: add rk3399 thermal_zones phandle
Signed-off-by: Olof Johansson <olof@lixom.net>

Device nodes representing I/O devices should be marked disabled in the
SoC-specific DTS, and overridden by board-specific DTSes where needed.

Fixes: 8e8b9eae ("arm64: dts: renesas: r8a7796: Add EthernetAVB instance")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Device nodes representing I/O devices should be marked disabled in the
SoC-specific DTS, and overridden by board-specific DTSes where needed.

Fixes: a92843c8 ("arm64: dts: r8a7795: add EthernetAVB device node")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Current r8a7795.dtsi defines audma -> ipmmu -> dma order.
Because of this order, dma can connect to ipmmu, but
audma can't connect to it.
This patch moves audma order as ipmmu -> dma -> audma.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Link the ARM GIC to the INTC-AP module clock, and add it to the SYSC
"always-on" PM Domain, so it can be power managed using that clock.

Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Link the ARM GIC to the INTC-AP module clock, and add it to the SYSC
"always-on" PM Domain, so it can be power managed using that clock.

Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Hien Dang <hien.dang.eb@renesas.com>
Signed-off-by: Thao Nguyen <thao.nguyen.yb@rvc.renesas.com>
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Hien Dang <hien.dang.eb@renesas.com>
Signed-off-by: Thao Nguyen <thao.nguyen.yb@rvc.renesas.com>
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This went unnoticed as the sata_rcar driver doesn't support Runtime PM
yet, but manages module clocks manually.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add initial dtsi file to support Hisilicon Hi3660 SoC with
support of Octal core CPUs in two clusters(4 * A53 & 4 * A73).

Also add dts file to support HiKey960 development board which
based on Hi3660 SoC.
The output console is earlycon "earlycon=pl011,0xfdf05000".
And the con_init uart5 with a fixed clock, which already
configured at bootloader.

When clock is available, the uart5 will be modified.

Tested on HiKey960 Board.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

Add arm cpu type cortex-a73
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

Add binding for hisilicon Hi3660 SoC and HiKey960 Board.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

Add this for supporting thermal calibration by e-fuse data.
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Add Cadence's eMMC controller node for LD11/LD20.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The LD11 SoC is equipped with SD-ctrl (0x59810000) as well as
MIO-ctrl (0x5b3e0000).  The SD-ctrl block on this SoC has just
one register for controlling RST_n pin of the eMMC device.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This pull request contains Broadcom ARM64-based SoC Device Tree changes for
4.11, please pull the following changes:

- Jon adds Device Tree nodes for the GICv2m and PAXB/PAXC PCIe interfaces on
  the Northstar 2 SoCs, he also enables PAXC on the Northstar 2 SVK reference
  board. He also updates the reserved memory entry for the Nitro firmware,
  required to get the on-chip NICs to work. Finally he adds support for the
  BCM958712DxXMC reference board which is a subset of existing boards.

* tag 'arm-soc/for-4.11/devicetree-arm64' of http://github.com/Broadcom/stblinux:
  arm64: dts: NS2: add support for XMC form factor
  arm64: dts: NS2: reserve memory for Nitro firmware
  arm64: dts: NS2: enable PAXC on NS2 SVK
  arm64: dts: NS2: enable GICv2m for PAXB/PAXC interfaces
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'juno-updates-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt64

ARMv8 Vexpress/Juno DT updates for v4.11

1. Addition of Coresight support on Juno R1 and R2 variants
2. Addition of STM(System Trace Macrocell) support on all Juno variants
3. Removed incorrect nesting of dtsi files
4. Removed untested USB hub only available on initial Juno R0 motherboard
5. Added ETR SMMU power domain and dma-ranges property

* tag 'juno-updates-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  arm64: dts: juno: remove motherboard USB node
  arm64: dts: juno: add ETR SMMU power domain
  arm64: dts: juno: add dma-ranges property
  arm64: dts: juno: add missing CoreSight STM component
  arm64: dts: juno: add CoreSight support for Juno r1/r2 variants
  arm64: dts: juno: refactor CoreSight support on Juno r0
  arm64: dts: juno: remove dtsi nesting inside tree structure
Signed-off-by: Olof Johansson <olof@lixom.net>

The first batch of Juno boards included a discrete USB controller chip
as a contingency in case of issues with the USB 2.0 IP integrated into
the SoC. As it turned out, the latter was fine, and to the best of my
knowledge the motherboard USB was never even brought up and validated.

Since this also isn't present on later boards, and uses a compatible
string undocumented and unmatched by any driver in the kernel, let's
just tidy it away for ever to avoid any confusion.
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

It is not at all clear from the documentation, but straightforward to
determine in practice, that the ETR SMMU is actually in the DEBUGSYS
power domain. Add that to the DT so that anyone brave enough to enable
said SMMU doesn't experience a system lockup on boot, especially a
sneaky one which goes away as soon as you connect an external debugger
to have a look at where it's stuck (thus powering up DEBUGSYS by other
means and allowing it to make progress again before actually halting...)
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

The interconnects around Juno have a 40-bit address width, and DMA
masters have no restrictions beyond their own individual limitations.
Describe this to ensure that DT-based DMA masks get set up correctly
for all devices capable of 40-bit addressing.
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

This patch adds the missing CoreSight STM component definition to the
device tree of all the juno variants(r0,r1,r2)

STM component is connected to different funnels depending on Juno
platform variant.
Reviewed-and-tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mike Leach <mike.leach@linaro.org>
[sudeep.holla@arm.com: minor changelog update and reorganising the STM
	node back into juno-base.dtsi to avoid duplication]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

The CoreSight support added for Juno is valid for only Juno r0.
The Juno r1 and r2 variants have additional components and alternative
connection routes between trace source and sinks.

This patch builds on top of the existing r0 support and extends it to
Juno r1/r2 variants.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mike Leach <mike.leach@linaro.org>
[sudeep.holla@arm.com: minor changelog update and major reorganisation of
	the common coresight components back into juno-base.dtsi to avoid
	duplication, also renamed funnel node names]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

Currently the Coresight components are supported only on Juno r0
variant. In preparation to add support to Juno r1/r2 variants, this
patch refactors the existing coresight device nodes so that r1/r2
support can be added easily.

It also cleans up some of the device node names which were previously
named so as they were confused as the labels rather than the node names.
Reviewed-and-tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

Currently juno-clock.dtsi and juno-base.dtsi are nested badly inside
the device tree structure. It's generally good practice to ensure that
individual dtsi stand by themselves at the top of the file.

This patch removes the nesting of the above mentioned dtsi files and
makes them independent.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

mvebu dt64 for 4.11 (part 1)

- Correct license text which was mangled when switching to dual license
- Add SPI and I2C nodes on Armada 3700(driver support had been already
  merged)
- Add support for the ethernet switch on the EspressoBin board (driver
  support not yet merged)

* tag 'mvebu-dt64-4.11-1' of git://git.infradead.org/linux-mvebu:
  ARM64: dts: marvell: Correct license text
  arm64: dts: marvell: Add I2C definitions for the Armada 3700
  arm64: dts: marvell: Enable spi0 on the board Armada-3720-db
  arm64: dts: marvell: Add definition of SPI controller for Armada 3700
  arm64: dts: marvell: Add ethernet switch definition for the ESPRESSObin
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'samsung-dt64-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64

Samsung DeviceTree ARM64 update for v4.11:
1. Add bus frequency and voltage scalling on Exynos5433 TM2 device (along with
   necessary bus nodes and Platform Performance Monitoring Unit on Exynos5433).
2. Use macros for pinctrl settings on Exynos5433.
   This contains necessary header with bindings.
3. Minor cleanups in Exynos5433 DTSI and boards using it.
4. Create common DTSI betweem Exynos5433 TM2E and TM2E.
5. Add HDMI/TV to Exynos5433 TM2.

* tag 'samsung-dt64-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  arm64: dts: exynos: Enable HDMI/TV path on Exynos5433-TM2
  arm64: dts: exynos: Add HDMI node to Exynos5433
  arm64: dts: exynos: Add DECON_TV node to Exynos5433
  arm64: dts: exynos: Fix addresses in node names on Exynos5433
  arm64: dts: exynos: Make TM2 and TM2E independent from each other
  arm64: dts: exynos: Fix wrong values for ldo23 and ldo25 on TM2/TM2E
  arm64: dts: exynos: Remove unsupported regulator-always-off property from TM2E
  arm64: dts: exynos: Comply to the samsung pinctrl naming convention in TM2
  arm64: dts: exynos: Use macros for pinctrl configuration on Exynos5433
  pinctrl: dt-bindings: samsung: add drive strength macros for Exynos5433
  arm64: dts: exynos: Add support of bus frequency using VDD_INT on Exynos5433 TM2
  arm64: dts: exynos: Add bus nodes using VDD_INT for Exynos5433
  arm64: dts: exynos: Add PPMU node to Exynos5433
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch adds support to volume-up key found on the board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

96Boards specs require all GPIO signals to be at 1.8V.
Limit MPP4, which is PIN28 on J8, to 1.8V(L5).
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

VOL/ZOOM+ button on DB410c is connected to
SoC GPIO 104. Add support for it.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

This patch adds support to hdmi audio via adv7533.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Fix typo in node name to reflect the correct pin name.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add the wcnss remoteproc node the SMD edge and the wcnss ctrl, bluetooth
and wifi nodes specified and enable this on db410c.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add SCM DT node to enable SCM functionality on MSM8996.
Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

The rpmcc driver is providing the XO clock, which is the parent of almost
all clocks. But during boot, this driver may probe later and leave most of
the clocks without parent. The common clock framework currently reports
invalid rate for orphan clocks and this may confuse drivers.

To resolve this, use fixed clocks registration until we have some support
to deal with the this issue. Removing the generic rpmcc compatible is
enough to switch back to fixed factor XO clock.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

The structure rockchip_clk_provider needs to refer the GRF regmap
in somewhere, if the CRU node has not "rockchip,grf" property,
calling syscon_regmap_lookup_by_phandle will return an invalid GRF
regmap, and the MUXGRF type clock will be not supported.

Therefore, we need to add them.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>