While mathematically it's ok to calculate the number of cyles for the
duty cycle as:

	duty_cycles = period_cycles * duty_ns / period_ns

this doesn't always give the right result when doing integer math. This
is best demonstrated using an example: With the input clock running at
208877930 Hz a request for duty_cycle = 383 ns and period = 49996 ns
results in

	period_cycles = clkrate * period_ns / NSEC_PER_SEC = 10443.06098828

Now calculating duty_cycles with the above formula gives:

	duty_cycles = 10443.06098828 * 383 / 49996 = 80.00024719

However with period_cycle truncated to an integer results in:

	duty_cycles = 10443 * 383 / 49996 = 79.99977998239859

So while a value of (a little more than) 80 would be the right result,
only 79 is used here. The problem here is that 14443 is a rounded result
that should better not be used to do further math. So to fix that use
the exact formular similar to how period_cycles is calculated.

Link: https://lore.kernel.org/r/7628ecd8a7538aa5a7397f0fc4199a077168e8a6.1710711976.git.u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

Giving an indication about the problem if probing a device fails is a
nice move. Do that for the stm32 pwm driver.
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20240315145443.982807-2-u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

Now that a pwm_chip has a dedicated struct device, pwmchip_set_drvdata()
and pwmchip_get_drvdata() can be made thin wrappers around
dev_set_drvdata() and dev_get_drvdata() respectively and the previously
needed pointer can be dropped from struct pwm_chip.

Link: https://lore.kernel.org/r/a5e05bd2d83421a26fdef6a87d69253c0f98becf.1710670958.git.u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

After assigning chip = pwm->chip; the compiler is free to assume that
pwm is non-NULL and so can optimize out the check for pwm against NULL.

While it's probably a programming error to pass a NULL pointer to
pwm_put() this shouldn't be dropped without careful consideration and
wasn't intended.

So assign chip only after the NULL check.
Reported-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/66a6f562-1fdd-4e45-995a-e7995432aa0c@baylibre.com
Fixes: 4c56b143 ("pwm: Add a struct device to struct pwm_chip")
Link: https://lore.kernel.org/r/20240329101648.544155-2-u.kleine-koenig@pengutronix.deReviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

This replaces the formerly dynamically allocated struct device. This
allows to additionally use it to track the lifetime of the struct
pwm_chip. Otherwise the new struct device provides the same sysfs API as
was provided by the dynamic device before.

Link: https://lore.kernel.org/r/35c65ea7f6de789a568ff39d7b6b4ce80de4b7dc.1710670958.git.u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

It's required to not free the memory underlying a requested PWM
while a consumer still has a reference to it. While currently a pwm_chip
doesn't live long enough in all cases, linking the struct pwm to the
pwm_chip results in the right lifetime as soon as the pwmchip is living
long enough. This happens with the following commits.

Note this is a breaking change for all pwm drivers that don't use
pwmchip_alloc().

Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org> # for struct_size() and __counted_by()
Link: https://lore.kernel.org/r/7e9e958841f049026c0023b309cc9deecf0ab61d.1710670958.git.u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

With the upcoming restructuring having all in a single file simplifies
things a bit. The relevant and somewhat visible changes are:

 - Some dropped prototypes from include/linux/pwm.h that were only
   necessary that core.c has a declaration of the symbols defined in
   sysfs.c. The respective functions are static now.

 - The pwm class now also exists if CONFIG_SYSFS isn't enabled. Having
   CONFIG_SYSFS is not very relevant today, but even without it the
   class and device stuff still provides lifetime tracking.

 - Both files had an initcall, these are merged into a single one now.
   Instead of a big #ifdef block for CONFIG_DEBUG_FS, a single
   if (IS_ENABLED(CONFIG_DEBUG_FS)) is used now. This increases compile
   coverage a bit and is a tad nicer on the eyes.

Link: https://lore.kernel.org/r/9e2d39a5280d7dda5bfc6682a8aef510148635b2.1710670958.git.u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

The code handling the sysfs API uses "child" and "parent" to refer to
the devices corresponding to a struct pwm or a struct pwm_chip
respectively.

Other parts of the pwm core use "parent" to refer to the parent device of
a struct pwm_chip.

So rename "child" to "pwm_dev" and "parent" to "pwmchip_dev" which
better explains the semantic. Also two functions are changed to match
the new names:

        child_to_pwm_export() -> pwmexport_from_dev()
        child_to_pwm_device() -> pwm_from_dev()

(which have the additional advantage to start with "pwm" which gives the
right scope). Additionally introduce a wrapper for dev_get_drvdata() to
convert a pwmchip_dev to the respective pwm_chip.

Link: https://lore.kernel.org/r/9cc05aceeae2f06ecb850bccb15ba821e768c183.1710670958.git.u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

While the compiler probably optimizes out the pointer dereference, using
the local variable holding the same value also benefits the human
reader. So simplify accordingly. Also move a loop over all capture lines
into the capture if block to group the operations related to capturing
in .probe().

Link: https://lore.kernel.org/r/a7a81f3838f7ed7f4d6dbee3d646989cc265f676.1710068192.git.u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

Using a multiplication to calculate the size of an allocation isn't
recommended in case the mulitplication overflows. While the chance this
happens is low, preventing such an error is easy enough; so do that.

Link: https://lore.kernel.org/r/17062aef42e6677629a056e25c6916d8b6eaedeb.1710068192.git.u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

Instead of (arbitrarily?) spliting the per-chip driver data into two
structures, put everything into struct sti_pwm_chip. This reduces memory
management overhead and a few pointer indirections.

Link: https://lore.kernel.org/r/2788a421ec838ee8f63e76a78b04e1d48b49f959.1710068192.git.u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

The .regfield member of struct sti_pwm_compat_data only holds a pointer
to the global array sti_pwm_regfields. Replace the few usages by
directly using this array and drop the member, saving a bit of memory
and a few pointer dereferences.

Link: https://lore.kernel.org/r/7ddb76ef49fd84a07713b46c65374cb51f3b4ac0.1710068192.git.u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

This has the advantage of handling EPROBE_DEFER correctly and being more
compact.

This change also introduces an error message for a few error paths that
lacked an error indicator before. Also sti_pwm_probe_dt() is renamed to
sti_pwm_probe_regmap() to better fit what it actually does.

Link: https://lore.kernel.org/r/8e540733ab882f2b8873712faf85c4f0cb48133a.1710068192.git.u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

Instead of of_clk_get_by_name() use devm_clk_get_prepared() which has
several advantages:

 - Combines getting the clock and a call to clk_prepare(). The latter
   can be dropped from sti_pwm_probe() accordingly.
 - Cares for calling clk_put() which is missing in both probe's error
   path and the remove function.
 - Cares for calling clk_unprepare() which can be dropped from the error
   paths and the remove function. (Note that not all error path got this
   right.)

With additionally using devm_pwmchip_add() instead of pwmchip_add() the
remove callback can be dropped completely. With it the last user of
platform_get_drvdata() goes away and so platform_set_drvdata() can be
dropped from the probe function, too.

Fixes: 378fe115 ("pwm: sti: Add new driver for ST's PWM IP")
Link: https://lore.kernel.org/r/81f0e1d173652f435afda6719adaed1922fe059a.1710068192.git.u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

Add compatible strings list for SAM9X7.
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240223172619.672262-1-varshini.rajendran@microchip.comSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

Memory holding a struct device must not be freed before the reference
count drops to zero. So a struct pwm_chip must not live in memory
freed by a driver on unbind. All in-tree drivers were fixed accordingly,
but as out-of-tree drivers, that were not adapted, still compile fine,
catch these in pwmchip_add().

Link: https://lore.kernel.org/r/35f5b229c98f78b2f6ce2397259a4a936be477c0.1707900770.git.u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

This prepares the aspeed-g6-pwm-tacho driver to further changes of the
pwm core outlined in the commit introducing devm_pwmchip_alloc(). There
is no intended semantical change and the driver should behave as before.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/e95e41eea5a138ae206c9116ba3cb1d9e0178284.1710777536.git.u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

struct pwm_chip::dev is about to change. To not have to touch this
driver in the same commit as struct pwm_chip::dev, use the accessor
function provided for exactly this purpose.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/5c6a11dd10cd29e0f7bfaa1fdef145523347cb58.1710777536.git.u.kleine-koenig@pengutronix.deSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

In the context of changing my career path, my Pengutronix email address
will soon stop to be available to me. Update the PWM maintainer entry to
my kernel.org identity.

I drop my co-maintenance of SIOX. Thorsten will continue to care for
it with the support of the Pengutronix kernel team.
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
Acked-by: Thorsten Scherer <t.scherer@eckelmann.de>
Link: https://lore.kernel.org/r/20240424212626.603631-2-ukleinek@kernel.orgSigned-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

Pull char / misc driver fixes from Greg KH:
 "Here are some small char/misc and other driver fixes for 6.9-rc5.
  Included in here are the following:

   - binder driver fix for reported problem

   - speakup crash fix

   - mei driver fixes for reported problems

   - comdei driver fix

   - interconnect driver fixes

   - rtsx driver fix

   - peci.h kernel doc fix

  All of these have been in linux-next for over a week with no reported
  problems"

* tag 'char-misc-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  peci: linux/peci.h: fix Excess kernel-doc description warning
  binder: check offset alignment in binder_get_object()
  comedi: vmk80xx: fix incomplete endpoint checking
  mei: vsc: Unregister interrupt handler for system suspend
  Revert "mei: vsc: Call wake_up() in the threaded IRQ handler"
  misc: rtsx: Fix rts5264 driver status incorrect when card removed
  mei: me: disable RPL-S on SPS and IGN firmwares
  speakup: Avoid crash on very long word
  interconnect: Don't access req_list while it's being manipulated
  interconnect: qcom: x1e80100: Remove inexistent ACV_PERF BCM

Pull kernfs bugfix and documentation update from Greg KH:
 "Here are two changes for 6.9-rc5 that deal with "driver core" stuff,
  that do the following:

   - sysfs reference leak fix

   - embargoed-hardware-issues.rst update for Power

  Both of these have been in linux-next for over a week with no reported
  issues"

* tag 'driver-core-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  Documentation: embargoed-hardware-issues.rst: Add myself for Power
  fs: sysfs: Fix reference leak in sysfs_break_active_protection()

Pull tty/serial driver fixes from Greg KH:
 "Here are some small tty and serial driver fixes for 6.9-rc5 that
  resolve a bunch of reported problems. Included in here are:

   - MAINTAINERS and .mailmap update for Richard Genoud

   - serial core regression fixes from 6.9-rc1 changes

   - pci id cleanups

   - serial core crash fix

   - stm32 driver fixes

   - 8250 driver fixes

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'tty-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: stm32: Reset .throttled state in .startup()
  serial: stm32: Return IRQ_NONE in the ISR if no handling happend
  serial: core: Fix missing shutdown and startup for serial base port
  serial: core: Clearing the circular buffer before NULLifying it
  MAINTAINERS: mailmap: update Richard Genoud's email address
  serial/pmac_zilog: Remove flawed mitigation for rx irq flood
  serial: 8250_pci: Remove redundant PCI IDs
  serial: core: Fix regression when runtime PM is not enabled
  serial: mxs-auart: add spinlock around changing cts state
  serial: 8250_dw: Revert: Do not reclock if already at correct rate
  serial: 8250_lpc18xx: disable clks on error in probe()

Pull USB / Thunderbolt driver fixes from Greg KH:
 "Here are some small USB and Thunderbolt driver fixes for 6.9-rc5.
  Included in here are:

   - MAINTAINER file update for invalid email address

   - usb-serial device id updates

   - typec driver fixes

   - thunderbolt / usb4 driver fixes

   - usb core shutdown fixes

   - cdc-wdm driver revert for reported problem in -rc1

   - usb gadget driver fixes

   - xhci driver fixes

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'usb-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
  USB: serial: option: add Telit FN920C04 rmnet compositions
  usb: dwc3: ep0: Don't reset resource alloc flag
  Revert "usb: cdc-wdm: close race between read and workqueue"
  USB: serial: option: add Rolling RW101-GL and RW135-GL support
  USB: serial: option: add Lonsung U8300/U9300 product
  USB: serial: option: add support for Fibocom FM650/FG650
  USB: serial: option: support Quectel EM060K sub-models
  USB: serial: option: add Fibocom FM135-GL variants
  usb: misc: onboard_usb_hub: Disable the USB hub clock on failure
  thunderbolt: Avoid notify PM core about runtime PM resume
  thunderbolt: Fix wake configurations after device unplug
  usb: dwc2: host: Fix dereference issue in DDMA completion flow.
  usb: typec: mux: it5205: Fix ChipID value typo
  MAINTAINERS: Drop Li Yang as their email address stopped working
  usb: gadget: fsl: Initialize udc before using it
  usb: Disable USB3 LPM at shutdown
  usb: gadget: f_ncm: Fix UAF ncm object at re-bind after usb ep transport error
  usb: typec: tcpm: Correct the PDO counting in pd_set
  usb: gadget: functionfs: Wait for fences before enqueueing DMABUF
  usb: gadget: functionfs: Fix inverted DMA fence direction
  ...

Pull scheduler fix from Borislav Petkov:

 - Add a missing memory barrier in the concurrency ID mm switching

* tag 'sched_urgent_for_v6.9_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Add missing memory barrier in switch_mm_cid

Pull x86 fixes from Borislav Petkov:

 - Fix CPU feature dependencies of GFNI, VAES, and VPCLMULQDQ

 - Print the correct error code when FRED reports a bad event type

 - Add a FRED-specific INT80 handler without the special dances that
   need to happen in the current one

 - Enable the using-the-default-return-thunk-but-you-should-not warning
   only on configs which actually enable those special return thunks

 - Check the proper feature flags when selecting BHI retpoline
   mitigation

* tag 'x86_urgent_for_v6.9_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpufeatures: Fix dependencies for GFNI, VAES, and VPCLMULQDQ
  x86/fred: Fix incorrect error code printout in fred_bad_type()
  x86/fred: Fix INT80 emulation for FRED
  x86/retpolines: Enable the default thunk warning only on relevant configs
  x86/bugs: Fix BHI retpoline check

Pull block fixes from Jens Axboe:
 "Just two minor fixes that should go into the 6.9 kernel release, one
  fixing a regression with partition scanning errors, and one fixing a
  WARN_ON() that can get triggered if we race with a timer"

* tag 'block-6.9-20240420' of git://git.kernel.dk/linux:
  blk-iocost: do not WARN if iocg was already offlined
  block: propagate partition scanning errors to the BLKRRPART ioctl

Pull email address update from James Bottomley:
 "My IBM email has stopped working, so update to a working email
  address"

* tag 'email' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  MAINTAINERS: update to working email address

Pull kvm fixes from Paolo Bonzini:
 "This is a bit on the large side, mostly due to two changes:

   - Changes to disable some broken PMU virtualization (see below for
     details under "x86 PMU")

   - Clean up SVM's enter/exit assembly code so that it can be compiled
     without OBJECT_FILES_NON_STANDARD. This fixes a warning "Unpatched
     return thunk in use. This should not happen!" when running KVM
     selftests.

  Everything else is small bugfixes and selftest changes:

   - Fix a mostly benign bug in the gfn_to_pfn_cache infrastructure
     where KVM would allow userspace to refresh the cache with a bogus
     GPA. The bug has existed for quite some time, but was exposed by a
     new sanity check added in 6.9 (to ensure a cache is either
     GPA-based or HVA-based).

   - Drop an unused param from gfn_to_pfn_cache_invalidate_start() that
     got left behind during a 6.9 cleanup.

   - Fix a math goof in x86's hugepage logic for
     KVM_SET_MEMORY_ATTRIBUTES that results in an array overflow
     (detected by KASAN).

   - Fix a bug where KVM incorrectly clears root_role.direct when
     userspace sets guest CPUID.

   - Fix a dirty logging bug in the where KVM fails to write-protect
     SPTEs used by a nested guest, if KVM is using Page-Modification
     Logging and the nested hypervisor is NOT using EPT.

  x86 PMU:

   - Drop support for virtualizing adaptive PEBS, as KVM's
     implementation is architecturally broken without an obvious/easy
     path forward, and because exposing adaptive PEBS can leak host LBRs
     to the guest, i.e. can leak host kernel addresses to the guest.

   - Set the enable bits for general purpose counters in
     PERF_GLOBAL_CTRL at RESET time, as done by both Intel and AMD
     processors.

   - Disable LBR virtualization on CPUs that don't support LBR
     callstacks, as KVM unconditionally uses
     PERF_SAMPLE_BRANCH_CALL_STACK when creating the perf event, and
     would fail on such CPUs.

  Tests:

   - Fix a flaw in the max_guest_memory selftest that results in it
     exhausting the supply of ucall structures when run with more than
     256 vCPUs.

   - Mark KVM_MEM_READONLY as supported for RISC-V in
     set_memory_region_test"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (30 commits)
  KVM: Drop unused @may_block param from gfn_to_pfn_cache_invalidate_start()
  KVM: selftests: Add coverage of EPT-disabled to vmx_dirty_log_test
  KVM: x86/mmu: Fix and clarify comments about clearing D-bit vs. write-protecting
  KVM: x86/mmu: Remove function comments above clear_dirty_{gfn_range,pt_masked}()
  KVM: x86/mmu: Write-protect L2 SPTEs in TDP MMU when clearing dirty status
  KVM: x86/mmu: Precisely invalidate MMU root_role during CPUID update
  KVM: VMX: Disable LBR virtualization if the CPU doesn't support LBR callstacks
  perf/x86/intel: Expose existence of callback support to KVM
  KVM: VMX: Snapshot LBR capabilities during module initialization
  KVM: x86/pmu: Do not mask LVTPC when handling a PMI on AMD platforms
  KVM: x86: Snapshot if a vCPU's vendor model is AMD vs. Intel compatible
  KVM: x86: Stop compiling vmenter.S with OBJECT_FILES_NON_STANDARD
  KVM: SVM: Create a stack frame in __svm_sev_es_vcpu_run()
  KVM: SVM: Save/restore args across SEV-ES VMRUN via host save area
  KVM: SVM: Save/restore non-volatile GPRs in SEV-ES VMRUN via host save area
  KVM: SVM: Clobber RAX instead of RBX when discarding spec_ctrl_intercepted
  KVM: SVM: Drop 32-bit "support" from __svm_sev_es_vcpu_run()
  KVM: SVM: Wrap __svm_sev_es_vcpu_run() with #ifdef CONFIG_KVM_AMD_SEV
  KVM: SVM: Create a stack frame in __svm_vcpu_run() for unwinding
  KVM: SVM: Remove a useless zeroing of allocated memory
  ...

Pull powerpc fixes from Michael Ellerman:

 - Fix wireguard loading failure on pre-Power10 due to Power10 crypto
   routines

 - Fix papr-vpd selftest failure due to missing variable initialization

 - Avoid unnecessary get/put in spapr_tce_platform_iommu_attach_dev()

Thanks to Geetika Moolchandani, Jason Gunthorpe, Michal Suchánek, Nathan
Lynch, and Shivaprasad G Bhat.

* tag 'powerpc-6.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  selftests/powerpc/papr-vpd: Fix missing variable initialization
  powerpc/crypto/chacha-p10: Fix failure on non Power10
  powerpc/iommu: Refactor spapr_tce_platform_iommu_attach_dev()

Pull clk fixes from Stephen Boyd:
 "A couple clk driver fixes, a build fix, and a deadlock fix:

   - Mediatek mt7988 has broken PCIe because the wrong parent is used

   - Mediatek clk drivers may deadlock when registering their clks
     because the clk provider device is repeatedly runtime PM resumed
     and suspended during probe and clk registration.

     Resuming the clk provider device deadlocks with an ABBA deadlock
     due to genpd_lock and the clk prepare_lock. The fix is to keep the
     device runtime resumed while registering clks.

   - Another runtime PM related deadlock, this time with disabling
     unused clks during late init.

     We get an ABBA deadlock where a device is runtime PM resuming (or
     suspending) while the disabling of unused clks is happening in
     parallel. That runtime PM action calls into the clk framework and
     tries to grab the clk prepare_lock while the disabling of unused
     clks holds the prepare_lock and is waiting for that runtime PM
     action to complete.

     The fix is to runtime resume all the clk provider devices before
     grabbing the clk prepare_lock during disable unused.

   - A build fix to provide an empty devm_clk_rate_exclusive_get()
     function when CONFIG_COMMON_CLK=n"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: mediatek: mt7988-infracfg: fix clocks for 2nd PCIe port
  clk: mediatek: Do a runtime PM get on controllers during probe
  clk: Get runtime PM before walking tree for clk_summary
  clk: Get runtime PM before walking tree during disable_unused
  clk: Initialize struct clk_core kref earlier
  clk: Don't hold prepare_lock when calling kref_put()
  clk: Remove prepare_lock hold assertion in __clk_release()
  clk: Provide !COMMON_CLK dummy for devm_clk_rate_exclusive_get()

jejb@linux.ibm.com no longer works.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Merge tag 'perf-tools-fixes-for-v6.9-2024-04-19' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools

Pull perf tools fixes from Namhyung Kim:
 "A random set of small bug fixes:

   - Fix perf annotate TUI when used with data type profiling

   - Work around BPF verifier about sighand lock checking

  And a set of kernel header synchronization"

* tag 'perf-tools-fixes-for-v6.9-2024-04-19' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
  tools/include: Sync arm64 asm/cputype.h with the kernel sources
  tools/include: Sync asm-generic/bitops/fls.h with the kernel sources
  tools/include: Sync x86 asm/msr-index.h with the kernel sources
  tools/include: Sync x86 asm/irq_vectors.h with the kernel sources
  tools/include: Sync x86 CPU feature headers with the kernel sources
  tools/include: Sync uapi/sound/asound.h with the kernel sources
  tools/include: Sync uapi/linux/kvm.h and asm/kvm.h with the kernel sources
  tools/include: Sync uapi/linux/fs.h with the kernel sources
  tools/include: Sync uapi/drm/i915_drm.h with the kernel sources
  perf lock contention: Add a missing NULL check
  perf annotate: Make sure to call symbol__annotate2() in TUI

Pull hardening fixes from Kees Cook:

 - Correctly disable UBSAN configs in configs/hardening (Nathan
   Chancellor)

 - Add missing signed integer overflow trap types to arm64 handler

* tag 'hardening-v6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  ubsan: Add awareness of signed integer overflow traps
  configs/hardening: Disable CONFIG_UBSAN_SIGNED_WRAP
  configs/hardening: Fix disabling UBSAN configurations

Pull iommufd fixes from Jason Gunthorpe:
 "Two fixes for the selftests:

   - CONFIG_IOMMUFD_TEST needs CONFIG_IOMMUFD_DRIVER to work

   - The kconfig fragment sshould include fault injection so the fault
     injection test can work"

* tag 'for-linus-iommufd' of git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd:
  iommufd: Add config needed for iommufd_fail_nth
  iommufd: Add missing IOMMUFD_DRIVER kconfig for the selftest

Pull rdma fixes from Jason Gunthorpe:

 - Add a missing mutex_destroy() in rxe

 - Enhance the debugging print for cm_destroy failures to help debug
   these

 - Fix mlx5 MAD processing in cases where multiport devices are running
   in switchedev mode

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  RDMA/mlx5: Fix port number for counter query in multi-port configuration
  RDMA/cm: Print the old state when cm_destroy_id gets timeout
  RDMA/rxe: Fix the problem "mutex_destroy missing"

Pull fs/9p fixes from Eric Van Hensbergen:
 "This contains a reversion of one of the original 6.9 patches which
  seems to have been the cause of most of the instability. It also
  incorporates several fixes to legacy support and cache fixes.

  There are few additional changes to improve stability, but I want
  another week of testing before sending them upstream"

* tag '9p-fixes-for-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  fs/9p: drop inodes immediately on non-.L too
  fs/9p: Revert "fs/9p: fix dups even in uncached mode"
  fs/9p: remove erroneous nlink init from legacy stat2inode
  9p: explicitly deny setlease attempts
  fs/9p: fix the cache always being enabled on files with qid flags
  fs/9p: translate O_TRUNC into OTRUNC
  fs/9p: only translate RWX permissions for plain 9P2000

Pull fuse fixes from Miklos Szeredi:

 - Fix two bugs in the new passthrough mode

 - Fix a statx bug introduced in v6.6

 - Fix code documentation

* tag 'fuse-fixes-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  cuse: add kernel-doc comments to cuse_process_init_reply()
  fuse: fix leaked ENOSYS error on first statx call
  fuse: fix parallel dio write on file open in passthrough mode
  fuse: fix wrong ff->iomode state changes from parallel dio write

Pull arm64 fixes from Catalin Marinas:

 - Fix a kernel fault during page table walking in huge_pte_alloc() with
   PTABLE_LEVELS=5 due to using p4d_offset() instead of p4d_alloc()

 - head.S fix and cleanup to disable the MMU before toggling the
   HCR_EL2.E2H bit when entering the kernel with the MMU on from the EFI
   stub. Changing this bit (currently from VHE to nVHE) causes some
   system registers as well as page table descriptors to be interpreted
   differently, potentially resulting in spurious MMU faults

 - Fix translation fault in swsusp_save() accessing MEMBLOCK_NOMAP
   memory ranges due to kernel_page_present() returning true in most
   configurations other than rodata_full == true,
   CONFIG_DEBUG_PAGEALLOC=y or CONFIG_KFENCE=y

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: hibernate: Fix level3 translation fault in swsusp_save()
  arm64/head: Disable MMU at EL2 before clearing HCR_EL2.E2H
  arm64/head: Drop unnecessary pre-disable-MMU workaround
  arm64/hugetlb: Fix page table walk in huge_pte_alloc()

Pull s390 updates from Alexander Gordeev:

 - Fix NULL pointer dereference in program check handler

 - Fake IRBs are important events relevant for problem analysis. Add
   traces when queueing and delivering

 - Fix a race condition in ccw_device_set_online() that can cause the
   online process to fail

 - Deferred condition code 1 response indicates that I/O was not started
   and should be retried. The current QDIO implementation handles a cc1
   response as an error, resulting in a failed QDIO setup. Fix that by
   retrying the setup when a cc1 response is received

* tag 's390-6.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/mm: Fix NULL pointer dereference
  s390/cio: log fake IRB events
  s390/cio: fix race condition during online processing
  s390/qdio: handle deferred cc1